To Next Page
S
Sara JordanSep 9, 2025
What to do if my Argox CP-3140 Barcode Reader says 'Media out'?
- AAndrea SantanaSep 9, 2025
If your Argox Barcode Reader displays 'Media out', install a new label roll.
What to do if my Argox CP-3140 Barcode Reader says 'Media out'?
If your Argox Barcode Reader displays 'Media out', install a new label roll.
What to do if my Argox CP-3140 Barcode Reader is in PAUSE status?
If your Argox Barcode Reader is in PAUSE status, press the FEED button to resume printing.
What to do if my Argox CP-3140 displays 'Ribbon Out'?
If your Argox Barcode Reader indicates 'Ribbon Out', install a new ribbon roll. Alternatively, if you do not require a ribbon, set the printing mode to “Direct Thermal” via the driver or commands.
What to do if my Argox Barcode Reader displays 'Media Out'?
If the Argox Barcode Reader shows a 'Media out' error, install a new label roll.
What to do if the cutter has failed, or there is a paper jam inside the cutter of my Argox CP-3140?
If the cutter has failed or there is a paper jam inside the cutter of your Argox Barcode Reader, check the cutter and recover any paper jam.
Why is my Argox Barcode Reader not indexing label gaps?
If your Argox Barcode Reader is not indexing label gaps, check the label path and the label sensor. If you are using a continuous label roll, configure the driver settings or commands to use “continuous media” printing.
What to do if my Argox Barcode Reader displays 'Serial IO error'?
If your Argox Barcode Reader displays a 'Serial IO error', check the serial baud rate on both your system and the printer.
What to do if my Argox CP-3140 Barcode Reader says 'Printer head module unlatched'?
If the printer head module of your Argox Barcode Reader is unlatched, close the printer module and press firmly on both the left and right sides to properly latch it.
What to do if my Argox Barcode Reader has a paper jam?
If your Argox Barcode Reader indicates a 'Paper jam', recover the jammed paper.
What to do if the printer head module is unlatched on my Argox CP-3140 Barcode Reader?
If the printer head module is unlatched on your Argox Barcode Reader, close the printer module and then press firmly on both the left and the right sides of the printer module to properly latch it.
States the proprietary nature of the manual's content.
Notes that product specifications are subject to change without notice.
Details compliance with FCC rules for Class A digital devices.
Argox's disclaimer regarding errors and liability for product use.
Instructions for checking the printer for shipping damage upon arrival.
Lists all accessories included with the printer.
Identifies the external components of the printer models.
Step-by-step instructions for connecting the power supply.
Instructions on preparing media rolls for loading.
Steps to physically place the media roll onto the hangers.
How to configure media types in software for specific label indexing.
Steps to prepare ribbon rolls for installation.
Instructions for mounting ribbon rolls onto the printer.
Step-by-step guide for installing the cutter module.
Procedure to calibrate the printer for optimal media performance.
Explains the content of the printer's configuration label.
Overview of available printer interfaces and their requirements.
Details for connecting via USB.
Steps to install the printer driver for USB connection.
Instructions to keep the print head in optimal condition for longevity.
Recommended frequency for cleaning print heads.
Specifies approved cleaning agents for the print head.
Proper wiping technique for cleaning the print head.
Overview of technical specifications for printer models.
Details on supported fonts, barcodes, and graphics.
Technical details of the USB interface.
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Weight | 2.5 kg |
| Resolution | 203 dpi |
| Print Speed | 4 ips |
| Print Width | 104 mm |
| Memory | 8 MB Flash, 8 MB SDRAM |
| Processor | 32-bit RISC |
| Interfaces | RS-232, USB, Parallel |
| Media Type | Roll, Fanfold |
| Media Width | 25.4 mm to 108 mm |
| Media Roll Diameter | 25.4 mm |
| Ribbon Length | 300 m |
| Ribbon Width | 33 mm to 110 mm |
| Ribbon Core Diameter | 25.4 mm |
| Power Source | AC 100-240V, 50/60Hz |
| Operating Temperature | 5°C to 40°C |
| Humidity | 25-85% non-condensing |
| Storage Temperature | -20°C to 50°C |
