Why ArjoHuntleigh Lifting Systems RTC function stops?
If the RTC (Return to Charge) function stops when hanging the hand control on the spreader bar of your ArjoHuntleigh Lifting Systems: * The lift detects a weight variation and cancels the RTC/RTH function. * Hang the hand control before activating the RTC/RTH function.
Why ArjoHuntleigh Lifting Systems beeps during utilization?
If your ArjoHuntleigh Lifting Systems lift emits a beep during use but the lowering function still works, it indicates that the batteries are low. Check if the display also shows a low battery indication and return the lift to the charging station.
What to do if ArjoHuntleigh Lifting Systems lift does not work?
If the ArjoHuntleigh Lifting Systems lift does not work when you press the buttons on the hand control: * Ensure the emergency stop is not activated by gently pushing up the Power On Switch to turn the unit back ON. * Check if the auxiliary up/down buttons on the lift (near the display) are working. If they are, the issue might be with the hand control. * If the auxiliary buttons don't work either, further assistance is needed.
Why ArjoHuntleigh Lifting Systems battery not full when charging?
If the battery level isn't full and the LED isn't flashing green when your ArjoHuntleigh Lifting Systems unit is on the charger: * Ensure the charger is properly plugged into a working standard outlet; the green light on the charging station should be on. * Verify that the two blades make good contact with the charging station. * Clean the lift contact blades and/or the contact plates of the charging station with a mild detergent, if necessary.
Why ArjoHuntleigh Lifting Systems batteries discharge quickly?
If your ArjoHuntleigh Lifting Systems batteries are always discharged after only a few transfers (3 to 5): * Place the lift on the charging station for at least 8 hours. * If the lift doesn't detect the charging station: * Ensure the charging station is plugged into a working standard outlet (the green light on the charging station should be lit). * Check that the contact blades make good contact with the charging station. Clean the unit blades and/or the contact plates of the charging station if necessary.
How to fix ArjoHuntleigh Lifting Systems LED light?
If the LED on your ArjoHuntleigh Lifting Systems does not light up at all, but the display is working properly: * Go to the “customize” menu and check if the LED is in the ENABLED state.
Why ArjoHuntleigh Lifting Systems ECS LED doesn't flash?
If, even with low batteries, the green LED on your ArjoHuntleigh Lifting Systems ECS doesn't flash 15 minutes after the last activation of the lift: * Ensure the wall charger is connected to a standard outlet. * Verify the wall charger outlet has power. * Check that the charger is connected to the ECS cable adapter on the fixed track. * Confirm all extensions used are connected properly. * Check for any interrupted contact strip along both sides of the track.
Why ArjoHuntleigh Lifting Systems ECS symbol still appears?
If, after an 8-hour continuous battery charging sequence, the ECS symbol still appears on the display and the green LED is still flashing on your ArjoHuntleigh Lifting Systems: * Press any button on the handset to wake up the LCD display; the battery icon should be full. If not, the batteries might not be charging, or the ECS system might be defective.
What to do if ArjoHuntleigh Lifting Systems lift passes the clip on the charging station?
If, when returning to charge, the ArjoHuntleigh Lifting Systems lift passes the clip on the charging station: * Ensure the charging station is plugged into a working standard outlet and has power (the green light on the charging station should be lit). * Clean the blades of the charging station with a mild detergent. * Check if the contact blades of the lift are clean and have good geometry. * Manually pass the lift through the charging station to see if it charges, then retry the RTC function.
Why ArjoHuntleigh Lifting Systems UP button doesn't work?
If only the UP button on the hand control of your ArjoHuntleigh Lifting Systems does not work: * Check if the strap is completely rolled inside the lift. * Check if the auxiliary UP button of the lift (located near the display) is working. If so, the problem may be coming from the hand control.
Emphasizes reading the manual thoroughly and explains warning symbols for safe operation.
Defines the lift's intended applications and provides crucial safety instructions for users.
Identifies and explains various labels and symbols found on the lift and its components.
Describes the hand control and control panel interface for operating the lift.
Explains the various icons and symbols that appear on the lift's display indicating status and alerts.
Procedures for initial lift setup, package verification, and essential checks before use.
How to access and adjust programmable parameters for lift operation.
Explains lift movement controls, sleep mode, and powered positioning systems.
How to access and interpret usage data for maintenance and operational history.
Details the manual emergency lowering mechanism and the automatic emergency brake.
Lists typical ArjoHuntleigh clip slings compatible with the Maxi Sky 2 ceiling lift.
Details compatibility of different spreader bars with various clip sling sizes.
Detailed steps for transferring patients from seated and supine positions using clip slings.
Lists various ArjoHuntleigh loop slings compatible with the Maxi Sky 2 ceiling lift.
Procedures for repositioning patients in bed, including lifting and turning techniques.
How the lift can be used to assist patients in rehabilitation training for gait improvement.
Overview of the KWIKtrak rail system and its accessories like gates and exchangers.
Instructions on how to move the lift laterally and in the facing direction using the X-Y rail system.
Using PPP stations for precise positioning of the lift along the rail layout.
Procedures for cleaning the lift and its special areas to maintain hygiene and functionality.
Guidelines for inspecting the lifting strap for wear and recommended maintenance intervals.
Troubleshooting guide for common problems like power, LED, beep, and battery status issues.
Key technical data for the Maxi Sky 2, including dimensions, electrical specs, and operating conditions.
Lists the standards and certifications the Maxi Sky 2 complies with.
Manufacturer's declaration and guidance on electromagnetic emissions and immunity of the lift.
Recommendations for minimum separation distances from RF communication equipment to prevent interference.
General| Type | Ceiling Lift |
|---|---|
| Power Source | Rechargeable Battery |
| Emergency Stop | Yes |
| Color | White |
| Lifting Height | Varies depending on installation |
| Lift Range | Varies depending on installation |
| Control | Hand control |
| Lifting Speed | 4 cm/s |
| Emergency Lowering | Manual |
| Wheel Configuration | N/A (Ceiling Lift) |
| Safe Working Load | 272 kg (600 lbs) |
| Maximum Weight Capacity | 272 kg (600 lbs) |
To Next Page
