Audio Technica ATW-T3202

Questions and Answers:

K
Kevin RogersAug 14, 2025
Why is there unwanted noise from my Audio Technica Receiver?
- C
  cameronaustinAug 14, 2025
  Unwanted noise can occur for several reasons. Make sure there isn't a noise source nearby, such as a fluorescent lamp or electrical component. Confirm each transmitter uses a different frequency. Check that the receiver's output terminal is correctly connected and that the receiver isn't sharing an outlet with another noisy component. Also, ensure no other nearby wireless systems use the same frequency band and adjust the squelch level if needed.
A
Amy WilsonAug 17, 2025
What to do if there is no voice output from Audio Technica Receiver?
- A
  allencassandraAug 17, 2025
  If you're not getting any sound, or the sound is very quiet, check these things: Make sure the transmitter and receiver channels are correctly set. Ensure that the power buttons on both the transmitter and receiver are turned on. Verify the antennas are properly connected. Confirm that all connected components, like a mixer, are correctly connected to the receiver. Check that the audio output and the audio output level of connected components are not set to the minimum.
L
Lisa BrownAug 21, 2025
How to fix distorted sound on Audio Technica Receiver?
- D
  Deborah ParkerAug 21, 2025
  Sound distortion can occur if the audio output level is too high, or if the volume of any connected component is too high. Ensure that the audio output level and the volume of connected components are not set too high.
M
Megan EllisAug 25, 2025
Why is the sound distorted on my Audio Technica ATW-T3202 Microphone system?
- V
  Virginia MooreAug 25, 2025
  If you're experiencing distorted sound with your Audio Technica Microphone system, ensure that the audio output level isn't set too high. Also, check that the volume of any connected components isn't excessively high.
C
Crystal SmithAug 27, 2025
What to do if there is no voice output from Audio Technica Microphone system?
- D
  daniellelunaAug 28, 2025
  If you're not getting any voice output or the voice output level is low on your Audio Technica Microphone system, verify the following: * Confirm that the transmitter/receiver channels are correctly set. * Ensure that the receiver's power button is turned ON. * Check that the antennas are properly connected. * Make sure all connected components, like a mixer, are correctly connected to the receiver. * Verify that the audio output isn't set to the minimum level. * Confirm that the audio output level of connected components (such as a mixer) is not minimized.
P
Paul LeeAug 31, 2025
How to reduce unwanted noise on Audio Technica Microphone system?
- K
  Kyle JacobsAug 31, 2025
  If you are experiencing unwanted noise with your Audio Technica Microphone system, check the following: * Ensure there isn't a noise source nearby, such as a fluorescent lamp or electrical component. * Verify that each transmitter uses a different frequency. * Confirm the receiver's output terminal is correctly connected. * Ensure the receiver isn't sharing an electrical outlet with another noisy component. * Check for other wireless systems nearby using the same frequency band and adjust the squelch level.
J
Jorge TerrySep 3, 2025
How to reduce unwanted noise in Audio Technica ATW-T3202?
- B
  baileytiffanySep 4, 2025
  If you're getting unwanted noise from your Audio Technica Microphone system, first check for nearby noise sources like fluorescent lamps or electrical components near the receiver. Make sure each transmitter uses a different frequency. Ensure the receiver's output terminal is correctly connected and that the receiver isn't powered from an outlet shared with a noisy component. Also, check for other wireless systems nearby using the same frequency band and adjust the squelch level accordingly.
R
Robin RhodesSep 7, 2025
Why is the voice output low on my Audio Technica Microphone system?
- B
  Bruce WatsonSep 7, 2025
  If you are experiencing no voice output or a low voice output level with your Audio Technica Microphone system, verify that the transmitter and receiver channels are correctly aligned. Also, ensure that the power switch is not turned off and that RF Power isn't off. Confirm that the transmitter isn't in mute mode and that the transmission output of the transmitter is not too low. Check that the microphone or the guitar cable is not disconnected (only for ATW- T3201). Confirm that the output volume of the musical instrument, such as a guitar, isn't set at the minimum level and that the microphone capsule is connected properly (only for ATW-T3202).
C
Cindy Caldwell MDSep 10, 2025
What causes unwanted noise in Audio Technica ATW-T3202 Microphone system?
- B
  Brooke WalkerSep 10, 2025
  If you're getting unwanted noise from your Audio Technica Microphone system, first check for nearby noise sources like fluorescent lamps, LED lamps, or electrical components near the transmitter. Make sure each transmitter uses a different frequency. Ensure the transmission output setting of the transmitter is not too high.

Audio Technica ATW-T3202 Specifications

General

Modulation	FM
RF Output Power	10 mW
Power Supply	2 AA batteries
Interchangeable capsule	Yes
Connector	XLR
Type	Handheld Transmitter
Operating Range	Up to 100 meters
Weight	290 g (10.2 oz)