What to do if my Audiovox Car Receiver will not power on?
If your Audiovox Car Receiver isn't powering on, there are a few things to check: * First, see if the radio fuse has blown and replace it with a new fuse that has the correct rating. * Also, check the car battery fuse and replace it if necessary with the correct type. * If the operation is illegal, try pressing the RESET button located over the rotary encoder on the front panel.
Why is there no or low audio output from my Audiovox Car Receiver?
If you're experiencing no or low audio output from your Audiovox Car Receiver, consider the following: * Ensure the audio output connection is properly wired. * Increase the volume level if it's set too low. * If the channel balance is heavily biased, adjust it to the center position. * Check for damaged speakers and replace them if needed. * Make sure that the speaker wiring isn't in contact with any metal parts of the car; if it is, insulate the connections.
What to do if my Audiovox Car Receiver unit resets itself when the engine is off?
If your Audiovox Car Receiver keeps resetting when the engine is off, the issue might be due to an incorrect connection between the ACC and the positive battery wire. Double-check the wiring and correct it if necessary.
Why does my Audiovox Car Receiver have poor sound quality or distortion?
Poor sound quality or distortion from your Audiovox Car Receiver can be caused by several factors: * If you're using a pirated disc, switch to an original copy. * Ensure that the speaker power rating is compatible with the unit; if not, connect the proper speakers. * Also, check the speaker contact to make sure the speaker isn't shorted.
Why is there no image on my Audiovox Car Receiver screen?
If there is no image on your Audiovox Car Receiver screen, it could be due to: * An incorrect connection to the parking brake wire: check the wiring and correct it if necessary. * The parking brake not being engaged: stop the vehicle in a safe place and apply the parking brake.
Why does my Audiovox Car Receiver have a flashing image or interference on the screen?
A flashing image or interference on your Audiovox Car Receiver screen can occur if: * The DVD is not compatible with the current TV system settings. Try changing the setup to accommodate the disc. * There are improper video signal connections. Inspect the wiring and correct as needed.
Why is the station searching weak on my Audiovox Car Receiver?
If your Audiovox Car Receiver has weak station searching, there are a few potential causes: * The auto antenna may not be fully extended or properly connected. Ensure the auto antenna control cable is correctly connected. * The LOCAL function might be activated. Try turning the LOCAL function off.
What to do if the disc does not play back on my Audiovox Car Receiver?
If a disc doesn't play back on your Audiovox Car Receiver, check these: * Make sure the disc isn't warped or scratched; use a disc in good condition. * If the disc is dirty or wet, clean it with a soft cloth. * The laser pickup might be dirty; clean it with a cleaning disc. * Confirm that you're using a compatible disc with the proper region code, inserted with the label side up.
Why can't I insert a disc into my Audiovox Car Receiver?
If you can't insert a disc into your Audiovox Car Receiver, it's possible that there is already a disc inside the unit. Eject the current disc before attempting to insert a new one.
Why is the image blurred, distorted, or dark on my Audiovox Car Receiver?
If the image on your Audiovox Car Receiver is blurred, distorted, or dark, it might be because you're using an illegally copied disc. Try using an original disc instead.
General| Resolution | 800 x 480 Pixels |
|---|---|
| Navigation | Yes |
| Bluetooth | Yes |
| USB Port | Yes |
| Audio Formats Supported | MP3, WMA |
| DVD Player | Yes |
| SD Card Slot | Yes |
| Rear View Camera Input | Yes |
| Radio | AM/FM |
| CD Player | Yes |
| Video Output | Yes |
| Aux Input | Yes |
| Video Formats Supported | MPEG-1, MPEG-2, MPEG-4 |
Essential safety precautions and warnings for the unit's operation and installation.
Explains the function of each button, connector, and slot on the device.
How to load, play, and eject discs, and control playback.
How to connect, insert, and play media from USB devices and SD/MMC cards.
Steps to connect a Bluetooth-enabled phone or device to the unit.
How to initiate phone calls and manage incoming calls using Bluetooth.
Steps for selecting language, accepting EULA, and configuring basic settings.
Methods to find and select a destination using address, POI, history, or map.
Solutions for power, audio output, sound quality, distortion, and unit resets.
Troubleshooting for display issues, interference, and weak station searching.
Solutions for discs not playing, blurred images, PBC errors, and disc errors.
To Next Page
