Autonics TZ4L - User Manual

H-72
TZN/TZ Series
Dual PID auto tuning control
※
1: Only for TZ4SP, TZ4ST, TZ4L, TZN4M
Series
.
Features
Ordering information
● Dual PID auto tuning function:
High-speed response of PID control to reach to the
desired value fast, low-speed of response of PID control
to minimize the overshoot even though response is a
little bit slow.
● High display accuracy: ±0.3%(by F.S. value of each input)
● 2-Steps auto tuning control function
● Multi-input function
(13 kinds of multi-input selection function):
Temperature sensor, voltage and current selection
function.
● Various sub output function:
Includes in LBA, SBA, 7kinds of alarm output and
4 kinds of alarm option function, PV transmission
output(DC4-20mA), RS485 communication output
● Display the decimal point for analog input
TZ4SP/TZN4S
TZN4
TZ4
TZ4/TZN4
Item
Digit
Size
Auxiliary output
Power supply
※
1
Control output
TZ4ST
Etc.
4 M 1 4 RTZ
R Relay output
S SSR drive voltage output
C Current output(DC4-20mA)
2 24VAC/24-48VDC
4 100-240VAC 50/60Hz
1 Event 1 output
1 Event 1 output
2 Event 1 + Event 2 output
R Event 1 + PV transmission output(DC4-20mA)
1 Event 1 output
2 Event 1 + Event 2 output
R Event 1 + PV transmission output(DC4-20mA)
A Event 1 + Event 2 + PV transmission output(DC4-20mA)
T Event 1 + RS485 communication output
B Event 1 + Event 2+RS485 communication output
S DIN W48×H48mm(terminal type)
SP DIN W48×H48mm(plug type)
ST DIN W48×H48mm(terminal type)
M DIN W72×H72mm
W DIN W96×H48mm
H DIN W48×H96mm
L DIN W96×H96mm
4 9999(4 digit)
TZ Temperature dontroller(PID)
TZN Temperature dontroller (PID New type)

Autonics TZ4L Specifications

General

Brand	Autonics
Model	TZ4L
Category	Controller
Language	English

Summary

Dual PID Auto Tuning Control

Features

Key characteristics of the Dual PID auto tuning control.

Ordering Information

Item

Details on how to specify the controller model and options.

Specifications

General Specifications

Overview of technical parameters like power, input, output, and control.

Performance Parameters

Details on accuracy, timing, resistance, and environmental conditions.

Connections

TZN4 S Wiring Diagram

TZN4 M Wiring Diagram

TZ4 SPTZ4 ST Wiring Diagram

TZ4 M Wiring Diagram

Parameter 1 Group Flowchart

Entering Parameter 1 Group

How to enter parameter 1 group from RUN mode using the MD key.

Parameter Settings (SV2, Alarms, Tuning)

Configuration of SV2, alarm limits, hysteresis, and PID tuning parameters.

Parameter 2 Group Configuration

Input, Event, Alarm & Auto-tuning Setup

Selecting input type, event modes, alarm type, and auto-tuning.

PID, Scaling & Communication Settings

PID type, temperature limits, scaling, communication speed, and address.

Ramp Function & Transmission Output

Alarm Functions

Alarm Operation Modes

Defines different alarm types (deviation, absolute value, sensor/loop break).

Key Functions Explained

Auto Tuning Process

PID auto tuning process for measuring system characteristics.

Sub Output and Alarm Functions

Control Methods

Dual PID Control Explained

High-speed or low-speed response PID control for precise temperature management.

RS485 Communication Setup

Input Correction and Output Connections

Input Correction & Analog Input Configuration

Output Connection Diagrams

Communication Protocol Details

Communication Interface Specifications

RS485 interface standard, speed, and communication protocol.

Command Structure and Examples

Structure and examples of read/write commands for measurement and settings.

Usage Guidelines and Cautions

Troubleshooting Load Operation and Errors

Installation and Electrical Cautions