To Next PageTo Next Page
Need help?Do you have a question about the Balboa TP500 and is the answer not in the manual?
General| Display Type | LCD |
|---|---|
| Backlight | Yes |
| Voltage | 12V DC |
| Operating Temperature | 0°C to 50°C (32°F to 122°F) |
| Humidity Range | 95% non-condensing |
| Weight | 0.5 lbs |
| Enclosure Rating | Water-resistant |
Identifier for the "Heat" function.
Indicates the spa is in "Ready Mode".
Indicates the spa is in "Rest Mode".
Indicates the "bba M2 On" feature is active.
Indicates WiFi connectivity status.
Controls or indicates the spa light status.
Indicates the cleanup cycle is running.
Controls or indicates the status of Jets 1.
Controls or indicates the status of Jets 2.
Controls or indicates the blower status.
Controls or indicates auxiliary functions.
Indicates the selected temperature range.
Used for programming and settings.
Indicates active filter cycles.
Indicates AM or PM for time display.
Explains how to navigate the control panel menus.
Describes the display sequence when the system powers up.
Explains symbols used in navigation diagrams.
Steps for filling the spa and initial setup.
Details the priming mode process after power-up.
Instructions on how to prime the spa pumps.
How to exit the priming mode manually or automatically.
How pumps operate, including speed and timeouts.
Describes different modes for the circulation pump.
Explains filtration cycles and ozone generator operation.
How the system protects against freezing.
Details the optional clean-up cycle after pump use.
How to change the spa's set temperature.
Using press-and-hold for continuous temp change.
Explanation of high and low temperature range settings.
How the spa maintains temperature in Ready Mode.
How the spa heats only during filter cycles in Rest Mode.
Special mode when "Jets" is pressed in Rest Mode.
Instructions for setting the current time.
How to invert the display orientation.
How to lock the control panel and temperature settings.
Sequence to unlock the panel or temperature.
Disables pumps for service functions for 1 hour.
Feature to employ pumps for draining spa water.
Setting start time and duration for Filter Cycle 1.
Configuration for an optional second filter cycle.
How pumps or blower purge plumbing at filter cycle start.
How to set up and use the light timer feature.
Change temperature display between Fahrenheit and Celsius.
Change clock display between 12-hour and 24-hour format.
Turn reminder messages display On or Off.
Set pump run time for the cleanup cycle.
Enable or disable M8 feature for reduced polling.
Set address for RF Dolphin Remote.
Configuring temperature units and time display format.
Adjusting reminder display and cleanup cycle duration.
Configuring M8 feature and Dolphin remote address.
Access system settings and identification.
Displays the system's software identification number.
Displays the specific model number of the system.
Shows the currently selected configuration setup.
Displays heater voltage, wattage, and type.
Lists available utilities like GFCI, A/B Sensors, Fault Log, Demo Mode.
Allows manual testing and resetting of the GFCI feature.
Displays temperature from Sensor A and Sensor B.
Records the last 24 faults for review.
Operates devices sequentially to demonstrate features.
Shows SSID, MODL, SETP, and voltage/wattage info.
Displays dip switch settings and panel software version.
Accesses GFCI test and A/B sensor temperature displays.
Accesses fault log and enables demo mode.
How to test and reset the GFCI protection feature.
Manually initiating the GFCI trip test.
Important warnings regarding GFCI testing and resets.
Explains what the fault log stores and how to access it.
Details on how to read fault messages, days, and temperatures.
Describes the spa's priming mode upon startup.
Messages for unknown temperature and high temperature.
Indicates when freeze protection is active.
Alerts like J29 Warning for heater disable input.
Messages for reduced or failed water flow to the heater.
Indicates when the heater may be dry or lacks water.
Alerts for the heater reaching excessive temperatures.
General messages indicating a reset may be needed.
Indicates potential desynchronization of temperature sensors.
Alerts for a failure in temperature sensor A or B.
Message indicating no communication with the system.
Indicates the system is running test software.
Alerts for memory checksum, persistent reset, or clock errors.
Indicates configuration issues or GFCI test failures.
Alerts for pumps appearing stuck ON, potentially overheating.
Message indicating the water level is too low.
Overview of scheduled maintenance reminders.
Prompts to check and adjust pH levels.
Prompts to check sanitizer and water chemistry.
Prompts to clean the filter media.
Prompts to test the GFCI regularly.
Prompts to change spa water regularly.
Reminders to clean and condition vinyl covers and wood skirting.
Prompts to replace filters for optimal function.
Reminders for mineral cartridge replacement and ozone generator check.
Prompts for scheduled service technician check-ups.
Requirements for safe and proper spa installation.
Importance of GFCI/RCD and owner testing.
Warnings against user service and electrical hazards.
Safety precautions and compliance information for CSA standards.
