Beckman Coulter Airfuge User Manual

Beckman Coulter Airfuge

56 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

AF-IM-13AC

June 2020

Instruction For Use

Airfuge

Air Driven Ultracentrifuge

Beckman Coulter, Inc.

250 S. Kraemer Blvd.

Brea, CA 92821 U.S.A.

Table of Contents

Other manuals for Beckman Coulter Airfuge

Instruction Manual56 pages

Questions and Answers:

D
Danielle GarciaSep 6, 2025
What to do if the rotor will not spin on my Beckman Coulter Laboratory Equipment?
- S
  Shelia BishopSep 6, 2025
  If the rotor on your Beckman Coulter Laboratory Equipment isn't spinning, there could be a few reasons. First, check the air and power connections to make sure they are properly connected. Also, verify that the circuit breaker hasn't tripped and reset it if necessary. Another potential cause is a saturated filter, which would require replacing the filter element. Inspect the stator pad for wear or damage and replace it if needed. Finally, ensure that the stator screws are tightened correctly.
D
David PerkinsSep 7, 2025
Why does my Beckman Coulter Airfuge Laboratory Equipment rotor run erratically or make noise?
- L
  Lauren FloresSep 8, 2025
  Erratic rotor behavior or unusual noises in your Beckman Coulter Laboratory Equipment can stem from several issues. A damaged stator pad could be the culprit, requiring replacement. Dirty air jets can also cause this problem, so cleaning the stator assembly is advised. Check for a missing or damaged rotor cap. Also, verify that the tubes or liner are correctly placed in the rotor.
B
Benjamin HuberSep 9, 2025
How to fix oil visibly collecting in Beckman Coulter Airfuge Laboratory Equipment?
- C
  Christopher MckaySep 9, 2025
  If you notice oil visibly collecting in your Beckman Coulter Laboratory Equipment, the filter element is likely saturated and needs to be replaced.
C
Christopher KnightSep 12, 2025
What to do if the Beckman Coulter Airfuge rotor fails to stop?
- J
  Joshua OdomSep 12, 2025
  If the rotor on your Beckman Coulter Laboratory Equipment isn't stopping, check if the brake pin shaft is oily and clean the pin and shaft. Also, the levitation air flow might be too high, so you should adjust it. Another possible cause is low brake spring tension, which also requires adjustment.
J
Jason PowellSep 12, 2025
Why does the Beckman Coulter Laboratory Equipment rotor stop too fast?
- J
  Jessica RichardsSep 12, 2025
  If the rotor on your Beckman Coulter Laboratory Equipment is stopping too quickly, it could be due to several reasons. The levitation air flow might be too low, requiring adjustment. Check the time-delay setting to ensure it's appropriate. A worn or damaged stator pad can also cause this, so consider replacing it. Also, clean the stator assembly and shaft in case the brake pin shaft is oily. Lastly, a brake malfunction may be the reason, so try adjusting the brake spring tension and levitation air.
K
Keith WigginsSep 14, 2025
What to do if pressure at Beckman Coulter Airfuge Laboratory Equipment will no longer read 30 psig?
- T
  Tammy SmithSep 14, 2025
  If the pressure reading on your Beckman Coulter Laboratory Equipment is no longer at 30 psig, the filter element is likely saturated and needs to be replaced.

Beckman Coulter Airfuge Specifications

General

Brand	Beckman Coulter
Model	Airfuge
Category	Laboratory Equipment
Language	English

Summary

Safety Notice

Electrical Safety

Details electrical safety precautions to prevent injury and damage.

Mechanical Safety

Covers safe operational practices to prevent mechanical injury or damage.

Chemical and Biological Safety

Addresses safe handling of chemical and biological materials during operation.

Description

Controls and Indicators

Identifies and describes the function of the instrument's controls and indicators.

Installation

Space and Location Requirements

Details the necessary space and environmental conditions for installation.

Electrical Requirements

Specifies the electrical power requirements for the instrument.

Operation

Starting the Run

Explains the steps involved in starting an ultracentrifuge run.

Ending the Run

Details the procedure for safely stopping and finishing an ultracentrifuge run.

Troubleshooting

Troubleshooting Guide

Lists common malfunctions, their causes, and recommended corrective actions.

Maintenance

Decontamination

Related product manuals

Preview: Beckman Coulter AU680

Beckman Coulter AU680

Preview: Beckman Coulter Avanti J-E

Beckman Coulter Avanti J-E

Preview: Beckman Coulter Allegra 25R

Beckman Coulter Allegra 25R

Preview: Beckman Coulter Allegra 64R

Beckman Coulter Allegra 64R

Preview: Beckman Coulter Avanti J-HC

Beckman Coulter Avanti J-HC

Beckman Coulter Allegra 21R

Beckman Coulter Avanti J-30 I

Preview: Beckman Coulter Avanti JXN-26

Beckman Coulter Avanti JXN-26

Preview: Beckman Coulter Avanti J Series

Beckman Coulter Avanti J Series

Preview: Beckman Coulter Allegra 6 Series

Beckman Coulter Allegra 6 Series

Preview: Allegra X-14 sERIES

Allegra X-14 sERIES