What to do if my BEKA PICO-troniX1 does not operate?
If your BEKA Water Pump isn't working, there could be several reasons. First, check if the pump is getting power by renewing the fuse if installed. If the fuse is fine, inspect the electric line for any breaks and renew if needed. If power isn't the issue, the pump itself or the integrated control unit might be defective, requiring replacement.
What to do if my BEKA Water Pump operates but does not deliver?
If your BEKA Water Pump runs but doesn't pump anything, it might be due to a few reasons. You may have an airlock in the delivery piston or air in the reservoir, in which case you should ventilate the pump. Also, check if the reservoir is empty and fill it up if needed. A defective level switch or pump element can also cause this problem, requiring you to exchange the control unit or the pump element.
Why is lubricant leaking at the pressure limiting valve of BEKA Water Pump elements?
If you find lubricant leaking at the pressure limiting valve of your BEKA Water Pump elements, it could be due to several reasons. The system pressure might be too high, so you should check the system. Alternatively, the progressive distributor could be blocked, requiring you to exchange the distributor. A blocked system, which requires you to repair blocked bearing, or a broken valve spring, which requires you to change the pressure limiting valve, could also be the cause.
What to do if my BEKA PICO-troniX1 is not switched off despite reservoir is empty?
If the BEKA Water Pump is not switching off even when the reservoir is empty, it's likely due to a defective level switch or integrated control unit. In either case, you'll need to exchange the control unit.
What to do if my BEKA Water Pump shows a level error but the reservoir is filled with lubricant?
If your BEKA Water Pump is showing a level error even though the reservoir is full, it indicates either a defective level switch or a defective integrated control. In both cases, the solution is to exchange the control unit.
Why is there no grease at some lube points with my BEKA PICO-troniX1 Water Pump?
If some lube points aren't getting any grease from your BEKA Water Pump, check the lines of the secondary distributor for bursts or leaks and exchange the line if needed. Also, inspect the fittings for leaks and retighten or change the fitting.
Why is there no grease at one lube point with my BEKA Water Pump?
If only one lube point isn't getting grease from your BEKA Water Pump, inspect the lubrication line for bursts or leaks and exchange the line if necessary. Also, check the fitting for leaks and retighten or change the fitting.
Why is the speed of my BEKA PICO-troniX1 reduced?
If your BEKA Water Pump's speed has reduced, it could be due to high system pressure. Check the system and bearing point for damage, and perform intermediate lubrication 1-2 times. Another possibility is that the supply voltage is too low, so you should check the voltage.
What to do if function of BEKA PICO-troniX1 do not match the set values in the control unit window?
If the function of your BEKA Water Pump (operating mode, cycle duration, or lubrication duration) doesn't match the set values in the control unit window, it's possible that the operating mode or setting of the control unit has been changed, but the old label was not replaced with the new one. To fix this, perform a diagnose by means of BEKA-DiSys software and have the setting correct according to the label, or change the label.
General| Brand | BEKA |
|---|---|
| Model | PICO-troniX1 |
| Category | Water Pump |
| Language | English |
General safety rules, symbols, hazards from non-compliance, and operator responsibilities.
Safety for maintenance, modification, operation modes, ESD, and hazard notes.
Guidelines for operating the pump according to regulations and intended use.
Describes pump assemblies and the operational mechanism of the PICO pump.
Level monitoring, unit functions, signals, data base, and parameter settings for PICO-troniX1.
Functions, modes, special features, error messages, and parameter changes for PICO-tronic.
Step-by-step guide to replacing the integrated control unit.
Common errors and their solutions for pump operation, delivery, and control unit issues.
To Next Page
