EasyManua.ls Logo

BendPak GP-7LC - User Manual

Default Icon
68 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: (800) 253-2363
Telephone: (805) 933-9970
bendpak.com
GrandPrix Two-Post Lifts
Installation and Operation Manual
Manual Revision C2 — August 2018 — Manual P/N 5900209
Models:
• GP-7
• GP-7LC
• GP-7LCS
Model GP-7 shown.
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠ DANGER
Read the entire contents of this manual before using this product.
Failure to follow the instructions and safety precautions in this
manual can result in serious injury or death. Make sure all other
operators also read this manual. Keep the manual near the product
for future reference. By proceeding with setup and operation, you
agree that you fully understand the contents of this manual.

Table of Contents

Other manuals for BendPak GP-7LC

Preview: Service Manual
Service Manual35 pages

Questions and Answers

  • J
    Joshua HolmesAug 8, 2025
    What to do if my BendPak GP-7LC lift does not raise or lower?
    • S
      Steven FloresAug 8, 2025
      If your BendPak Lifting Systems lift isn't raising or lowering, here are a few things to check: * Ensure there's enough hydraulic fluid in the reservoir. * Make sure there's no air in the hydraulic system. * Inspect the hydraulic lines for pinches or leaks. * Verify the power unit is receiving power. * If the hydraulic fluid is dirty, replace it. * Confirm the lift isn't overloaded.
  • M
    Mark AnthonyAug 13, 2025
    Why is my BendPak Lifting Systems motor not running?
    • A
      Amanda AlexanderAug 13, 2025
      If the motor of your BendPak Lifting Systems is not running, check the connection to the power source to ensure it is properly plugged in and receiving the correct voltage. You may also want to consult the wiring diagram for further assistance.
  • C
    Cheyenne CarterAug 17, 2025
    What to do if hydraulic fluid is dirty in BendPak Lifting Systems?
    • M
      Margaret TurnerAug 17, 2025
      If the hydraulic fluid in your BendPak Lifting Systems is dirty, replace it with clean, approved ATF fluids, such as Dexron III, Dexron VI, Mercon V, Mercon LV, or comparable.
  • C
    carsoncliffordAug 21, 2025
    Why BendPak GP-7LC Lifting Systems lift does not stay up?
    • W
      William RosarioAug 21, 2025
      If your BendPak Lifting Systems lift isn't staying up, ensure that you are only leaving the lift on its safety locks. Also, check for any hydraulic fluid leaks.
  • C
    charleswatsonAug 26, 2025
    How to fix odd noises in BendPak Lifting Systems?
    • A
      Andrea BradyAug 26, 2025
      To address odd noises in your BendPak Lifting Systems lift, lubricate the hinge points using white lithium grease.
  • B
    Brian RuizAug 30, 2025
    What to do if BendPak GP-7LC arms move erratically or squeak?
    • L
      Luke GreenAug 30, 2025
      If the arms on your BendPak Lifting Systems lift move erratically or squeak during use, try moving the arms up and down a few times. This action helps flush out any residual air from the hydraulic system.
  • A
    Alexandria LunaSep 3, 2025
    What to do if there is no pressure from pump in BendPak Lifting Systems?
    • B
      Bethany DuranSep 3, 2025
      If there's no pressure from the pump in your BendPak Lifting Systems, prime the pump.

BendPak GP-7LC Specifications

General IconGeneral
Lifting Capacity7, 000 lbs
Weight1, 450 lbs. / 658 kg
Motor2 HP
Power Requirement220V
Drive-Thru Clearance96 inches
Minimum Height4 inches
Power Requirements220V

Related product manuals