What to do if an error in the state machine of the detector has occurred in Berthold Duo Measuring Instruments?
If an error in the state machine of the detector has occurred in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if the actual HV has reached the upper HV limit on Berthold Measuring Instruments?
If the actual HV has reached the upper HV limit (HV > 1287V, bzw. HV > 1300V - 1%) on your Berthold Measuring Instruments, contact BERTHOLD. The detector must be checked and replaced if necessary.
What to do if the actual HV has reached the lower HV limit on Berthold Duo?
If the actual HV has reached the lower HV limit (HV < 303V, bzw. HV < 300V + 1%) on your Berthold Measuring Instruments, contact BERTHOLD. The detector must be checked and replaced if necessary.
Why is there no count rate in the measuring channel of my Berthold Duo?
If there is no count rate in the measuring channel of your Berthold Measuring Instruments, the photomultiplier may be defective. Check the photomultiplier or contact BERTHOLD.
What to do if I get a system error on Berthold Duo Measuring Instruments?
If a system error occurs in your Berthold Measuring Instruments, and the event occurs frequently, contact BERTHOLD.
What to do if the voltage of the RID channel deviates from the admissible set value in Berthold Duo?
If the voltage of the RID channel deviates from the admissible set value in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if the voltage of the control channel deviates from the admissible set value in Berthold Measuring Instruments?
If the voltage of the control channel deviates from the admissible set value in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if the voltage of the auxiliary channel deviates more than allowed from the control value in Berthold Duo?
If the voltage of the auxiliary channel deviates more than allowed from the control value in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if the current high voltage deviates from the average high voltage by more than 20% in Berthold Duo Measuring Instruments?
If the current high voltage deviates from the average high voltage by more than 20% in your Berthold Measuring Instruments, check the detector electronics and photomultiplier. If necessary, contact BERTHOLD.
What to do if there is an error in the high-voltage supply of the photomultiplier in Berthold Duo?
If an error in the high-voltage supply of the photomultiplier was detected in your Berthold Measuring Instruments, check the detector electronics and photomultiplier. If necessary, contact BERTHOLD.
Essential instructions for safe operation and handling of the product.
Defines correct usage of the detectors and outlines improper usage scenarios.
Details required qualifications for personnel handling the device.
Lists the operator's responsibilities for personnel training and product monitoring.
Explains the radiometric measurement principle and system components.
Critical safety warnings and precautions for installation procedures.
Guidance on how to install mounting clamps for detectors.
Step-by-step guide for the initial electrical setup and connection of the detector.
System requirements and connection details for using the PC software.
Explanation of the PC software's structural design and control options.
Schematic structure of the detector menu within the PC software.
Procedures for restarting the detector or resetting to factory settings.
List of possible device event messages and troubleshooting options.
Safety precautions for maintenance and repair work, especially in hazardous areas.
Procedure for updating the device software using the Detector Service Modem.
Steps for removing and installing a complete detector unit.
Instructions for replacing the detector's electronics module.
Essential instructions for safe operation and handling of the product.
Defines correct usage of the detectors and outlines improper usage scenarios.
Details required qualifications for personnel handling the device.
Lists the operator's responsibilities for personnel training and product monitoring.
Explains the radiometric measurement principle and system components.
Critical safety warnings and precautions for installation procedures.
Guidance on how to install mounting clamps for detectors.
Step-by-step guide for the initial electrical setup and connection of the detector.
System requirements and connection details for using the PC software.
Explanation of the PC software's structural design and control options.
Schematic structure of the detector menu within the PC software.
Procedures for restarting the detector or resetting to factory settings.
List of possible device event messages and troubleshooting options.
Safety precautions for maintenance and repair work, especially in hazardous areas.
Procedure for updating the device software using the Detector Service Modem.
Steps for removing and installing a complete detector unit.
Instructions for replacing the detector's electronics module.
General| Brand | Berthold |
|---|---|
| Model | Duo Series |
| Category | Measuring Instruments |
| Language | English |
To Next Page
