Why is there no count rate in the auxiliary channel of my Berthold LB 4700 Measuring Instruments?
If there is no count rate in the auxiliary channel of your Berthold Measuring Instruments, the photomultiplier may be defective. Check the photomultiplier or contact BERTHOLD.
What to do if my Berthold Security Sensors show a hardware error?
Contact Berthold. The hardware is defective and, if necessary, must be checked and replaced.
What to do if the Berthold Security Sensors detector temperature is too high or too low?
If the detector is too hot: Install/check water cooling system. If the detector is too cold: Install/check heating.
How to fix a corrupted HW module in Berthold LB 4700?
If the HW module is corrupted in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if the temperature sensor of the detector is defective in Berthold LB 4700?
If the temperature sensor of the detector is defective in your Berthold Measuring Instruments, contact BERTHOLD. The hardware is defective and, if necessary, must be checked and replaced.
What to do if the count rate fluctuates more than permissible in Berthold LB 4700 Measuring Instruments?
If the count rate fluctuates more than permissible in your Berthold Measuring Instruments, and the event occurs frequently, contact BERTHOLD.
What to do if the temperature sensor of the detector is defective in Berthold Security Sensors?
Contact Berthold. The hardware is defective and, if necessary, must be checked and replaced.
What to do if the actual HV has reached the upper HV limit in Berthold Security Sensors?
Contact BERTHOLD. Detector must be checked and replaced if necessary.
What to do if an error in the state machine of the detector has occurred in Berthold LB 4700 Measuring Instruments?
If an error in the state machine of the detector has occurred in your Berthold Measuring Instruments, restart the device. If the event occurs frequently, contact BERTHOLD.
What to do if Berthold Security Sensors has an error when reading the Pt100 input?
Restart the device. If the event occurs frequently, contact Berthold. The event must be confirmed manually.
Lists related documents for the manual.
Declares compliance with EU directives.
Refers to safety manual for approvals and certificates.
Explains symbols for manual, ESD, earth, and equipotential connections.
Explains the manual's purpose, scope, validity, and target audience.
Explains chapter structure and representation conventions.
Explains warning levels (DANGER, WARNING, CAUTION) and their meanings.
Provides instructions for safe operation and storage.
Defines proper and improper use of the detectors.
Defines personnel roles (General Knowledge, Experts, Authorized Persons).
Outlines operator responsibilities for personnel training and monitoring.
Explains how detectors measure radiation intensity.
Specifies conditions for storing the devices.
Details the various components of the detectors.
Provides warnings for installation, including falling loads and explosion hazards.
Instructions for checking the delivery for completeness and damage.
Details on how to install mounting clamps for detectors.
Describes methods for installing detectors on pipelines using clamping devices.
Details on mounting detectors on vessels using mounting clamps.
Explains installation of detectors on conveyor belts using measuring frames.
Step-by-step guide for initial setup and electrical connections.
Important notices regarding the reuse of previously used detectors.
Outlines the different user interfaces for operating the detector.
Details system requirements and connection procedures for PC software.
Explains the structural design and control options of the PC software interface.
Describes the schematic structure of the detector menu within the PC software.
Safety precautions for maintenance and repair, including explosion hazards.
Describes updating device software using the Detector Service Modem.
Guidance on visually inspecting scintillator and photomultiplier for errors.
Steps for replacing the detector, including parameter transfer.
Safety instructions and procedures for replacing the electronics module.
Safety instructions and steps for removing and installing the scintillator.
Instructions for replacing the scintillator/multiplier combination.
Optional system to protect scintillators from high temperatures.
Kit required for operation in extended temperature range (-40°C to +100°C).
Optional lead collimator to protect against background radiation.
Notes on toxic components and proper disposal procedures.
General| Brand | Berthold |
|---|---|
| Model | LB 4700 |
| Category | Measuring Instruments |
| Language | English |
To Next Page
