Why is my Binder FD 53 Climate chamber not working?
Your Binder Climate chamber might not be working due to several reasons. First, check the connection to the power supply. Second, the chamber fuse might have responded, so check it and replace it if needed. If it responds again, contact BINDER service. Finally, the controller could be defective, in which case you should also contact BINDER service.
What to do if Binder FD 53 set-point temperature is not reached?
If the set-point temperature isn't reached in your Binder Climate chamber, ensure the chamber door is completely closed. Also, inspect the door gasket and replace it if it’s defective. Calibrate and adjust the controller. Finally, check the power supply to ensure the voltage is correct (115V or 230V).
Why Binder FD 53 Climate chamber doesn’t heat up but controller display working?
If your Binder Climate chamber isn’t heating up, and the red heating control light is off but the controller display is working, it could be due to the timer being run off. Program the timer or switch to continuous operation. Another cause might be a defective semiconductor relay, in which case you should contact BINDER service.
What to do if Binder FD 53 isn't working and the red alarm light is on?
If your Binder Climate chamber isn't working and the red alarm pilot lamp is lit, it could be that the safety device class 2 has turned off the chamber. Let the chamber cool down and then press the RESET button. Also, the safety device class 2 might be defective, in that case contact BINDER service.
Why is my Binder Climate chamber heating permanently?
If your Binder Climate chamber is heating permanently and not maintaining the set-point, the controller may be defective, in that case contact BINDER service. Alternatively, the controller might need calibration and adjustment.
How to fix high temperature and red alarm on Binder FD 53?
If the temperature inside your Binder Climate chamber is too high and the red alarm light is on, the safety device class 3.1 may have been triggered. Check the settings of the temperature set-point and of the safety device class 3.1.
Why does my Binder FD 53 take longer to heat up?
If you're experiencing deviations from the indicated heating-up times with your Binder Climate chamber, it might be because the chamber is fully loaded. Try loading the chamber with fewer items or allow for longer heating-up times.
Why is my Binder Climate chamber in stand-by mode?
If your Binder Climate chamber is without function and only the green 'stand-by' LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
What to do if Binder FD 53 Climate chamber fan is not working?
If the fan in your Binder Climate chamber isn’t turning or is turning too slowly, the fan might be defective, in that case contact BINDER service.
Why does my Binder FD 53 Climate chamber controller return to normal display?
If the controller on your Binder Climate chamber returns to the Normal Display from any level, it's likely because no button was pressed for approximately 30 seconds. Repeat your entries, entering the values more rapidly.
Provides general safety guidelines for installation and operation, including ventilation and unauthorized accessories.
Specifies the intended applications for the chambers and lists prohibited uses.
Details the safety measures implemented by the manufacturer to prevent ignition and explosions.
Procedures and precautions for safely lifting and transporting the chamber, including weight considerations.
Details on how to electrically connect the chamber, including power plug types and voltage specifications.
Step-by-step guide on how to power on and initialize the chamber.
How to view and set the desired temperature without using a temperature ramp.
How to view and set temperature set-points when a temperature ramp function is active.
Explains the two available time functions: continuous operation and timer operation.
Accessing and modifying user-specific settings like temperature units and chamber addressing.
Details on the function, operation, and setting of the Class 2 temperature safety device for ED/FD models.
Details on the function, operation, and setting of the Class 3.1 temperature safety device for BD models and optional for ED/FD.
Instructions for cleaning the chamber after use and procedures for decontamination if contamination occurs.
Comprehensive technical specifications for BINDER BD models, covering dimensions, electrical data, and temperature performance.
Comprehensive technical specifications for BINDER ED models, covering dimensions, electrical data, and temperature performance.
Comprehensive technical specifications for BINDER FD models, covering dimensions, electrical data, and temperature performance.
General| Temperature Range | 0 °C to 100 °C |
|---|---|
| Humidity Range | 10% to 80% RH |
| Interior Volume | 53 L |
| Power Supply | 230 V, 50/60 Hz |
| Temperature Fluctuation at 25°C | ±0.3 °C |
| Humidity Fluctuation at 25°C/60% RH | ±2% RH |
| Heat-up time to 100°C | 45 min |
| Number of Shelves (Standard/Max) | 2/4 |
| Max. Load per Shelf | 15 kg |
| Max. Permissible Load | 40 kg |
To Next Page
