To Next PageTo Next PageWhat to do if my Binder APT.line FD 53-UL unit has no function?
If your Binder unit isn't functioning at all, start by checking the power supply connection. If that's okay, inspect the unit fuse and replace it if necessary. If the fuse blows again, contact BINDER service.
Why is the set-point temperature not reached in my Binder Accessories?
If the set-point temperature in your Binder Accessories unit isn't reached after the specified time, make sure the unit door is completely closed. Also, check if the door gasket is defective and replace it if needed. Ensure that the controller is calibrated and adjusted correctly, and verify that the power supply matches the voltage requirements (115V or 230V).
How to turn on Binder APT.line FD 53-UL unit if only the green stand-by LED is lit?
If your Binder unit is only showing the green “stand-by” LED, it's likely in stand-by mode. Press and hold the ON/OFF button until the display illuminates.
What to do if temperature is too high and the red alarm pilot lamp is lit in Binder APT.line FD 53-UL?
If the temperature inside the chamber of your BD, option ED, FD Binder Accessories unit is too high and the red alarm pilot lamp of safety device is lit, check the temperature set-point and the safety device class 3.1 settings.
What to do if Binder APT.line FD 53-UL Accessories unit doesn't function and the red alarm pilot lamp is lit?
If your ED, FD Binder Accessories unit isn't working and the red alarm pilot lamp is lit, the safety device class 2 may have shut down the chamber. Allow the chamber to cool down, then press the RESET button. Check the temperature set-point and the safety device class 2 settings, and select a suitable limit value if necessary.
What to do if Binder Accessories chamber doesn’t heat up and the red light is off?
If the chamber in your Binder Accessories unit isn't heating up, and the red heating control light in the display is not lit but the controller display is working, ensure the timer is correctly programmed or set to continuous operation.
Why are there deviations from heating-up times in Binder APT.line FD 53-UL?
To address deviations from the indicated heating-up times in your Binder oven, reduce the oven load or allow for longer heating-up times.
Why is my Binder Accessories chamber heating permanently?
If the chamber in your Binder Accessories unit is heating permanently and the set-point isn't being held, calibrate and adjust the controller.
Why does the Binder Accessories controller return to Normal Display?
If the controller returns to the Normal Display from any level, repeat entries and enter the values rapidly, because no button was hit for more than 60 sec.
What to do if fan doesn’t turn in Binder Accessories?
If the fan in your FD Binder Accessories unit isn't turning or is turning too slowly, contact BINDER service.
Essential safety guidelines for installation and operation.
Defines approved applications and limitations for the equipment.
Procedures for safely handling and moving the unit.
Details how to connect the unit to the power supply.
Step-by-step guide for powering on the equipment.
How to set desired temperature, with or without ramp functions.
Explanation of continuous and timer-based operation modes.
Accessing and modifying user-specific controller settings.
Details the function and operation of the Class 2 safety device.
Details the function and operation of the Class 3.1 safety device.
Information on connecting the unit to communication software.
Recommended maintenance schedules and service procedures.
Procedures for cleaning and decontaminating the unit.
Essential safety guidelines for installation and operation.
Defines approved applications and limitations for the equipment.
Procedures for safely handling and moving the unit.
Details how to connect the unit to the power supply.
Step-by-step guide for powering on the equipment.
How to set desired temperature, with or without ramp functions.
Explanation of continuous and timer-based operation modes.
Accessing and modifying user-specific controller settings.
Details the function and operation of the Class 2 safety device.
Details the function and operation of the Class 3.1 safety device.
Information on connecting the unit to communication software.
Recommended maintenance schedules and service procedures.
Procedures for cleaning and decontaminating the unit.
General| Manufacturer | Binder |
|---|---|
| Interior Volume | 53 L |
| Product Type | Drying Oven |
| Model | FD 53-UL |
| Temperature Range | Ambient +5°C to 300°C |
| Power Supply | 230 V |
| Display | LCD |
| Shelves | 2 shelves |
