What to do if my Binder Laboratory Equipment chamber doesn’t heat up and the red heating control light is off?
If your Binder Laboratory Equipment chamber isn’t heating up, the red heating control light is off, but the controller display is working, the timer may have run off. Program the timer or switch to continuous operation.
Why is my Binder FED 720 Laboratory Equipment chamber heating permanently?
If your Binder Laboratory Equipment chamber is heating permanently and the set-point isn't being held, the controller might be defective, so it's recommended to contact BINDER service. The Pt 100 sensor might also be defective. Calibrate and adjust the controller.
What to do if my Binder FED 720 Laboratory Equipment set-point temperature is not reached?
If the set-point temperature isn't reached in your Binder Laboratory Equipment after the specified time, ensure the chamber door is completely closed. If that doesn't solve the issue, the door gasket may be defective and need replacement. Also, calibrate and adjust the controller. Verify that the power supply matches the voltage requirement of 115V or 230V.
Why won't my Binder Laboratory Equipment chamber heat up, but the red heating control light is on?
If your Binder Laboratory Equipment chamber isn't heating up, and the red heating control light is on, the heating element may be defective, so it's recommended to contact BINDER service. Also, a semiconductor relay might be defective.
What to do if my Binder FED 720 temperature is too high and the red alarm light is on?
If the temperature inside your Binder Laboratory Equipment chamber is too high and the red alarm light is on, check the settings of the temperature set-point and of the safety device class 3.1.
What to do if my Binder Laboratory Equipment chamber has no function?
If your Binder Laboratory Equipment chamber isn't working, first check the connection to the power supply. Also, inspect the chamber fuse and replace it if needed. If the fuse blows again, it is recommended to contact BINDER service.
What to do if Binder FED 720 Laboratory Equipment chamber has no function?
First, check the connection to the power supply. If that's not the issue, the overtemperature protective device class 1 might have turned off the chamber. Disconnect the chamber from the power supply for at least 10 seconds and let it cool down. If the device responds again, further assistance is needed.
Why are there deviations from the indicated heating-up times in my Binder Oven?
Deviations from the indicated heating-up times in your Binder Oven can occur if the chamber is fully loaded. Reduce the load or allow longer heating-up times.
Why does the fan in my Binder Oven not turn or turns too slowly?
If the fan in your Binder Oven doesn’t turn or turns too slowly, first check if the fan speed is set too low and set the fan speed to 100%. If the problem persists, contact Binder service.
Why is my Binder Oven chamber without function, with only the green stand-by LED lit?
If your Binder Oven chamber has no function and only the green “stand-by” LED is lit, the chamber is likely in stand-by mode. Press the ON/OFF button until the display lights up.
Requirements for personnel operating the chamber, including training and authorization.
Explanation of safety symbols, signal words, and warning panels.
Broad safety advice for chamber installation, operation, and ventilation.
Defines the proper applications and limitations of the chamber.
Details the control panel, its display, and functional buttons.
Steps for verifying the received chamber and its accessories.
Safety precautions and procedures for moving the chamber.
Requirements for the chamber's installation site and environmental conditions.
Detailed steps for connecting the chamber to the power supply.
Explanation of controller buttons, display, and status symbols.
How to set target temperature and fan speed parameters.
Procedure to set or change access passwords for controller functions.
Description of the basic overtemperature safety device.
Details on the adjustable electronic safety controller.
How to configure the limit temperature for the safety controller.
Actions to take when an alarm is triggered by safety devices.
Overview of the three available timer modes: Delayed Off, Temp. Dependent Delayed Off, Delayed On.
Instructions for setting the delayed-off timer.
How to input timer duration and fan settings for Delayed Off.
Steps for setting a temperature-dependent timer.
Inputting parameters for the temperature-dependent timer.
Steps for setting the delayed-on timer.
Inputting parameters for the delayed-on timer.
How to configure and view ramp settings, gradient, and target set-point.
Monitoring and adjusting ramp target values.
Steps to initiate data logging to a USB stick.
Steps to stop data logging and retrieve recorded data.
Procedures for cleaning chamber surfaces and components.
Methods for disinfecting the chamber after contamination.
Basic steps to resolve common operational issues.
General| Brand | Binder |
|---|---|
| Model | FED 720 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
