Need help?Do you have a question about the Blink TP-EVPD-30kW and is the answer not in the manual?
No serviceable items inside; high voltage can cause severe injury or death. Only factory qualified personnel can repair.
Do not operate with damaged cable or exposed wires. Shut off power and contact service.
System contains AC/DC high voltage; install only by qualified electricians trained for high voltage systems.
Equipment designed to meet ADA requirements per 2010 ADA Standards for Accessible Design.
Warnings regarding open doors with power on and residual high voltage in components after power disconnect.
Specifies input voltage (480 VAC, 3 Phase+N+E, 60Hz) and current (40 Amps).
Charger should be installed above 4 ft from the ground on a stable wall or pole.
The charger utilizes a Wall Mount. Dimensions are provided.
Input cables must be copper (3P+N+PE), flexible preferred, with proper cable ducting.
Requires reliable protective grounding, preferably dedicated, with low resistance.
Use a 3P+N breaker with suitable capacity (e.g., 1.25x FLA) as per NEC.
Use copper lugs for cables; avoid flammable materials near the station.
Recommend a canopy for harsh weather; confirm site load capacity.
Touchscreen display for instructions, feedback, services, payment, and error messages.
Safety measure; pressing it immediately stops all charging activity.
Identifies EV drivers by their RFID card placed on the pad.
Allows placement of DCFC connector cables for ease of use and storage.
Instructions for lifting and positioning the charger using forklift cut-outs and a mounting bracket.
Step-by-step guide to mounting the charger bracket and fixing the charger securely.
Steps to start a charging session using a registered RFID card.
Steps to start a charging session using a QR code or mobile app.
Steps to start a charging session using a credit card, ensuring sufficient balance.
Allow 1 minute after powering down before servicing internal components due to residual high voltage.
Periodic checks (3-6 months) for voltage, grounding, filter, power module lights, and cables.
Checks for abnormal sound, odor, appearance, or dust/dirt; contact service if issues arise.
Standard 2-year parts warranty; optional service plans cover parts and labor.
Limited warranty covers defects in materials/workmanship for two years from shipment/installation.
Excludes damage from wear, misuse, accidents, acts of nature, unauthorized modifications, or improper installation.
No serviceable items inside; high voltage can cause severe injury or death. Only factory qualified personnel can repair.
Do not operate with damaged cable or exposed wires. Shut off power and contact service.
System contains AC/DC high voltage; install only by qualified electricians trained for high voltage systems.
Equipment designed to meet ADA requirements per 2010 ADA Standards for Accessible Design.
Warnings regarding open doors with power on and residual high voltage in components after power disconnect.
Specifies input voltage (480 VAC, 3 Phase+N+E, 60Hz) and current (40 Amps).
Charger should be installed above 4 ft from the ground on a stable wall or pole.
The charger utilizes a Wall Mount. Dimensions are provided.
Input cables must be copper (3P+N+PE), flexible preferred, with proper cable ducting.
Requires reliable protective grounding, preferably dedicated, with low resistance.
Use a 3P+N breaker with suitable capacity (e.g., 1.25x FLA) as per NEC.
Use copper lugs for cables; avoid flammable materials near the station.
Recommend a canopy for harsh weather; confirm site load capacity.
Touchscreen display for instructions, feedback, services, payment, and error messages.
Safety measure; pressing it immediately stops all charging activity.
Identifies EV drivers by their RFID card placed on the pad.
Allows placement of DCFC connector cables for ease of use and storage.
Instructions for lifting and positioning the charger using forklift cut-outs and a mounting bracket.
Step-by-step guide to mounting the charger bracket and fixing the charger securely.
Steps to start a charging session using a registered RFID card.
Steps to start a charging session using a QR code or mobile app.
Steps to start a charging session using a credit card, ensuring sufficient balance.
Allow 1 minute after powering down before servicing internal components due to residual high voltage.
Periodic checks (3-6 months) for voltage, grounding, filter, power module lights, and cables.
Checks for abnormal sound, odor, appearance, or dust/dirt; contact service if issues arise.
Standard 2-year parts warranty; optional service plans cover parts and labor.
Limited warranty covers defects in materials/workmanship for two years from shipment/installation.
Excludes damage from wear, misuse, accidents, acts of nature, unauthorized modifications, or improper installation.
General| Power Output | 30 kW |
|---|---|
| Type | DC Fast Charger |
| Charging Mode | Mode 3 |
| Cooling Method | Liquid Cooled |
| Operating Temperature | -30°C to 50°C |
| Protection Features | Overvoltage, overcurrent, overtemperature, ground fault |
| Connector Type | CCS |
To Next Page
