EasyManua.ls Logo

Blue Clean 240 - User Manual

Blue Clean 240
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model: 240
AR240-04-2012
www.arblueclean.com
Owner’s Manual

Table of Contents

Questions and Answers

  • J
    Jason AdkinsJul 31, 2025
    How to fix a Blue Clean 240 Pressure Washer that will not turn on?
    • W
      William RogersJul 31, 2025
      First, ensure the Blue Clean Pressure Washer is in the “OFF” position. Then, plug the electrical cord into a grounded 120-volt outlet, avoiding any extension cords. If the plug doesn't fit, the outlet isn't properly grounded, so try another outlet. Press the reset button on the GFCI power box; if the red color isn't visible in the small window, unplug and replug, then press reset again, ensuring the red color remains visible. If it does, turn the power switch to “ON” and squeeze the spray gun trigger. If it still doesn't work, try another outlet and repeat the process.
  • D
    Dawn WelchAug 5, 2025
    Why is my Blue Clean Pressure Washer leaking water at the hose connection?
    • L
      Lucas TurnerAug 5, 2025
      If water is leaking where the high pressure hose connects to the spray gun of your Blue Clean Pressure Washer, make sure there is an o-ring at the end of the metal tip of the high pressure hose. If no o-ring is present, the connection between the hose and spray gun will leak.
  • T
    Travis Garcia Jr.Aug 10, 2025
    How to connect the high pressure hose to the spray gun on a Blue Clean Pressure Washer?
    • K
      kellysandovalAug 10, 2025
      To connect the high pressure (HP) hose to the spray gun of your Blue Clean Pressure Washer, wiggle, twist and/or pull the rubber sleeve covering the fitting at the end of the high pressure hose down until the entire tip is visible plus an 1/8” of the metal fitting below the tip. Now try to insert the hose tip into the spray gun. It should “click” into place and will not come out until the hose is released by pushing in the lever on the underside of the gun. If you're still having trouble, you may carefully cut away the end of the sleeve with a sharp knife, being cautious not to damage the hose.
  • J
    John SandersAug 14, 2025
    What to do if Blue Clean Pressure Washer turns on then off?
    • M
      Michelle StaffordAug 15, 2025
      When the water is connected, the accessories are assembled properly, and the power switch is turned on, your Blue Clean Pressure Washer may turn on for 1 - 2 seconds to prime the pump. It automatically shuts off and waits for the spray gun trigger to be pressed. When the trigger is pressed, water starts flowing through the pump. The water sensor in the pump “senses” the moving water and automatically turns the power washer on. Alternatively, turn the power switch off, hold in the trigger on the spray gun, so that you have a steady stream of water. While you are holding the trigger open on the spray gun, at the same time, turn the power switch on.
  • A
    Aaron BallardAug 19, 2025
    What to do if I can’t remove the lance from the spray gun of my Blue Clean Pressure Washer?
    • D
      Dana BrownAug 19, 2025
      To remove the lance from the spray gun of your Blue Clean Pressure Washer, press the spray gun and lance together (about a 1/8”) and turn counter clockwise and the lance will slide out. Alternatively, hold the spray gun and lance in an upright position with the nozzle end on the floor. Push the whole assembly straight down to loosen the connection, and then follow the removal process again. You may also spray soapy water or a lubricant in the area where the lance connects to the spray gun.
  • P
    patricia08Aug 26, 2025
    What to do if my Blue Clean 240 Pressure Washer runs but has no water flow?
    • T
      tabithaleeAug 26, 2025
      If your Blue Clean Pressure Washer is running but there's no water flow, check the water source. Additionally, unclog the nozzle on the lance, referring to the nozzle cleaning instructions under “Cleaning nozzles”. You can also try removing the lance and spraying directly from the spray gun to determine if the lance is the issue.

Summary

Introduction

Safeguards Warnings and Safety Tips

Servicing of a Double-Insulated Appliance

Package Contents

Unpacking & Assembly

High Pressure Hose

Connects the high pressure hose to the unit and spray gun.

Spray Gun

How to use the spray gun, including trigger lock and safety.

Lance and Detergent bottle

Attaching lances and detergent bottle to the spray gun.

Garden Hose Adapter

Connecting the garden hose adapter and filter to the water inlet.

Operating Instructions

Operating Tips and Maintenance

Cleaning nozzles

Instructions for clearing clogged or partially clogged spray nozzles.

How to Avoid Damaging Surfaces

Guidance on preventing surface damage during cleaning operations.

Detergent Bottle

Details on using the detergent bottle and correct mixture ratios.

Storage

Pump Saver

Pump Saver Instructions

Step-by-step procedure for using Pump Saver to protect the pump.

Troubleshooting and FAQs

Replacement Parts

Specifications

Limited Warranty

Warranty Returns

Blue Clean 240 Specifications

General IconGeneral
ModelBlue Clean 240
TypeElectric Pressure Washer
Max Pressure2400 PSI
Hose Length20 ft
Power Cord Length35 ft
Power SourceElectric
Warranty1 Year
Motor Power13 Amps

Related product manuals