The AR Blue Clean BC111HS is an electric pressure washer designed for various cleaning projects. It offers a powerful 1600 PSI (pounds per square inch) maximum pressure and a 1.7 GPM (gallons per minute) maximum flow rate, making it suitable for tackling dirt and grime on different surfaces. The rated pressure is 1160 PSI, and the rated flow rate is 1.2 GPM. It operates on a standard 120-volt, 60 Hz electrical supply, drawing 12.5 amps, and has a weight of 14.6 lbs, making it relatively portable.
Function Description:
The primary function of the BC111HS is to clean surfaces using a high-pressure stream of water. It connects to a standard garden hose for water supply and plugs into a grounded 120-volt outlet. The unit features an auto-start feature, where it primes itself for 1-2 seconds and then shuts off, waiting for the spray gun trigger to be pressed to begin operation. This design helps conserve energy and prolong pump life. The pressure washer is equipped with a Ground Fault Circuit Interrupter (GFCI) built into the power cord plug, which enhances safety by reducing the risk of electric shock.
Important Technical Specifications:
- Model: BC111HS
- Max PSI: 1600 lbs/sq. in.
- Rated PSI: 1160 lbs/sq. in.
- Max GPM: 1.7 Gal/per min
- Rated GPM: 1.2 Gal/per min
- Cold Water: Yes (designed for cold water use only)
- Volts: 120
- Frequency: 60 Hz
- Amps: 12.5
- Weight: 14.6 lbs
Usage Features:
The BC111HS comes with several accessories to enhance its versatility:
- Spray Gun (F): The main control for directing the high-pressure water. It includes a safety lock (G) to prevent accidental engagement of the trigger.
- Extension Lance (I): Attaches to the spray gun to provide extended reach and allows for the connection of various nozzles.
- 15° Quick Connect Nozzle (J): A general-purpose nozzle for a balanced spray pattern.
- Foam Cannon (H): Designed for applying detergents. It has a straw that fits into the high-pressure top and allows for adjustment of soap levels. Users should only use detergents specifically formulated for power washers and avoid thick or gel-like detergents to prevent clogging.
- Super Soft High Pressure Hose (E): Connects the power washer unit to the spray gun. It is crucial to tighten this hose properly to prevent it from slipping or popping off during use.
- Cord Hook (D) and Spray Gun Holster (A): Integrated storage solutions on the unit for convenience and organization.
- Handle (B): For easy transport and maneuverability.
To operate the unit, users must first ensure the "ON/OFF" switch is in the "OFF" position, plug the GFCI into a grounded outlet, and fully open the water supply. Before turning on the power, the spray gun trigger should be squeezed to release air and allow a steady stream of water. Once the power switch is turned "ON," the unit will briefly run and then shut off, indicating it's ready for use. Squeezing the trigger on the spray gun initiates the high-pressure wash. Users are advised to allow the motor to come to a complete stop before squeezing the trigger again to prevent issues with the auto-start feature. Always test a small area to avoid damaging surfaces, as the impact force of the water can exceed the durability of certain materials. The force can be varied by adjusting the angle and distance of the nozzle from the surface.
Maintenance Features:
Regular maintenance is essential to ensure the longevity and optimal performance of the BC111HS:
- Nozzle Cleaning: Clogged nozzles can significantly reduce water pressure or cause the unit to pulsate. The unit includes a nozzle cleaning wire (L) for clearing debris. Alternatively, an unfolded paper clip can be used. After cleaning, back-flush water through the nozzles using a garden hose.
- Garden Hose Adapter Screen: The screen inside the garden hose adapter should be cleaned periodically to prevent debris from entering the pump. It can be removed, rinsed with clean water, and reinserted.
- O-Rings: The o-rings on the bayonet end of the nozzle should be cleaned regularly and lubricated with non-water soluble grease, such as petroleum jelly, to prevent leaks. An O-Ring Kit (K) is included for replacements.
- Detergent System: After using the foam cannon, any remaining detergent should be discarded, and the bottle and nozzle head flushed with fresh water to prevent chemical residue from clogging the injector.
- Storage: Proper storage is crucial, especially in freezing temperatures. The power washer should be stored indoors to prevent water in the unit from freezing and expanding, which can cause damage. If outdoor storage is unavoidable, a pump saver (not included, part # PW64511) is recommended to protect the pump from freezing and internal corrosion. Before storing, the unit should be turned off, unplugged, water supply disconnected, and all remaining water pressure released by squeezing the spray gun trigger. The high-pressure hose and lance should be removed, and the gun placed in its holster. The power cord and pressure hose have designated storage hooks on the unit.
The manufacturer provides a 2-year warranty for the product. The first year covers all parts and accessories, while the second year covers manufacturer defects. For any questions, problems, or missing parts, customers are encouraged to contact AR North America's customer service department via phone or email.
To Next Page
General
