How to fix no sound from loudspeakers of all Bosch Conference System Discussion Devices?
If there is no sound coming from the loudspeakers of all discussion devices, the loudspeaker volume may be too low. Use the volume control button on the control unit or the web browser interface to increase the volume.
Why is the sound faint or distorted from my Bosch CCS 1000 D Conference System discussion device?
Faint or distorted sound from a discussion device can occur if one or more trunk lines are overloaded. To fix this, reduce the load on the trunk lines by either decreasing the number of discussion devices or shortening the length of the extension cables.
What to do if there is no sound from the loudspeaker of a Bosch CCS 1000 D Conference System discussion device?
If there is no sound from the loudspeaker of a discussion device, check if headphones are connected. If they are, remove the headphones.
How to fix faint or distorted sound from Bosch CCS 1000 D discussion device?
Faint or distorted sound from a discussion device can occur if one or more trunk lines are overloaded. To resolve this, reduce the load on the trunk lines by either reducing the number of discussion devices or reducing the length of the extension cable(s).
Why is there acoustic feedback from my Bosch CCS 1000 D Conference System discussion devices?
Acoustic feedback occurs when there's a sound loop between a loudspeaker and a microphone. To resolve this: * Reduce the volume of all discussion devices using the control unit. * Decrease the volume of the control unit loudspeaker. * Increase the distance between the discussion devices and/or the control unit. * Increase the distance between the headphone and the microphone.
What to do if my Bosch CCS 1000 D microphone does not respond?
If the microphone is not responding, one or more trunk lines may be overloaded. Reduce the load by either reducing the number of discussion devices or shortening the length of the extension cables.
Why is there a brief interruption in the audio during a Bosch CCS 1000 D meeting/discussion?
Brief audio interruptions during a meeting or discussion can happen if recorder settings or individual microphone outputs are changed during the session. Avoid changing these settings during a meeting.
Why is there no sound from the loudspeakers of all Bosch Conference System discussion devices?
If there is no sound from the loudspeakers of all discussion devices, it may be because the loudspeaker volume is too low. Use the volume control button on the Control Unit or web browser interface to centrally increase the volume of all Discussion Devices.
What to do if the Bosch Conference System microphone does not respond?
If the microphone does not respond, one or more trunk lines might be overloaded. Reduce the load on the trunk lines by either reducing the number of discussion devices or reducing the length of the extension cable(s).
Why is there no sound from the loudspeaker of a Bosch CCS 1000 D discussion device?
If there is no sound from the loudspeaker of a discussion device, check if headphones are connected to the discussion device. If they are, remove the headphones.
Instructions for installing the Control Unit and Extension Unit in a rack or on a table.
Describes how to connect the main system components like Control Unit and Discussion Devices.
Details the rear panel connections of the CCSD-CURD Control Unit.
Explains the connections for the Discussion Device, including headphone and trunk connections.
Details the rear panel connections of the CCSD-EXU Extension Unit.
Instructions on how to configure a device as a chairperson's device.
Steps to initialize a Discussion Device for the first time.
Procedure to erase the address of a Discussion Device.
Guide for initial setup and connection to the web browser interface.
Instructions for first-time login and normal login procedures.
How to view and control waiting and speaker lists, and manage recordings.
How to define discussion settings like mode, speakers, and waiting options.
Functions for managing recordings, including playback and saving.
Detailed guide on using the MP3 recorder for discussions.
Step-by-step instructions for creating recordings using USB memory sticks.
Methods for playing back recorded discussions via web browser or PC.
A table listing common problems, causes, and solutions for the system.
General| Number of Participants/Devices | Up to 100 |
|---|---|
| Total Harmonic Distortion | <0.1 % |
| Signal-to-noise ratio (Microphone) | > 65 dB |
| System Type | Digital |
| Microphone Type | Gooseneck |
| Speech Activation | Yes |
| Power Supply (VAC) | 100-240 VAC |
To Next Page
