To Next PageTo Next PageWhy can’t I read back history with # 89 input on my Bosch Security System?
You can't read back history on your Bosch Security System with #89 input if you're entering from a Master keypad or not using a PIN with test authority. First enter Single Partition Mode. Use a PIN with test authority.
Why doesn't Chime Mode (#7) work when a zone is faulted on my Bosch DS7400Xi Security System?
If Chime Mode (#7) isn't working when a zone is faulted on your Bosch Security System, it could be because it's not activating for interior zones, or the keypad isn't assigned to the same partition as the zone being activated. Chime mode only activates for perimeter zones and must be programmed. Also, if the perimeter zone has trouble enabled (trouble on open), the chime won’t work if that zone is opening. Chime mode will only activate the sounder on keypads that are assigned to the same partition as the zone.
Why are reports for partitions 2-8 being sent with partition 1’s reporting ID on my Bosch Security System?
If reports for partitions 2-8 are being sent with partition 1’s reporting ID on your Bosch Security System, it means the account codes for partitions 2-8 are either not programmed or programmed incorrectly. Check addresses 3429-3459 to ensure they are correctly configured.
Why can't I reset my Bosch DS7400Xi Security System to factory default?
If you're unable to reset your Bosch Security System to the factory default settings, it might be because the keypad programming access is set to PARTIAL from a Remote programmer. Change the setting to FULL using the Remote programmer to regain full access.
Why some functions don’t work on a Master keypad of Bosch DS7400Xi Security System?
Some functions on your Bosch Security System require you to enter single partition mode when using a Master keypad. The following commands require that you are in Single Partition Mode when entering from a Master keypad: • History read-back • Chime mode • Checking zone status • Checking zone trouble status (after #87 - Master keypad will show only partition name) • Bypassing zones.
Why is my Bosch Security System not sending open or close reports?
If your Bosch Security System isn't sending open or close reports, it's likely due to incorrect programming. Check addresses 3331, 3332, 3334, and 3333 to ensure they are correctly configured.
Why can't I perform a zone test (#81) on my Bosch DS7400Xi?
You can't perform a zone test on your Bosch Security System if you're entering from a Master keypad, or if you're not using a PIN with test authority. Use a PIN with test authority.
Why does my Bosch Security System keypad display 'Not Programmed, See Instal Guide'?
If your Bosch Security System keypad displays 'Not Programmed, See Instal Guide,' the sounder is on, and the keypad doesn't work, it could be due to a few reasons. The keypad might not be addressed correctly, it might not be programmed properly, or keypads 11-15 are not configured correctly. Ensure the keypad jumper is properly installed in the back. Then, check keypad programming addresses 3131-3138, and verify keypad addresses 11-15. Keep in mind that the system will only recognize keypads on the options bus.
Why is my Bosch DS7400Xi not transmitting history to WDSRP?
If your Bosch Security System panel isn't transmitting history to WDSRP, it could be due to a couple of reasons. First, check the programming to ensure it's set to send history. Also, make sure the time and date are correctly set on the panel.
Why does my Bosch Security System display 'Entry Error: Please Re-enter'?
If your Bosch Security System keypad displays 'Entry Error: Please Re-enter' and beeps continuously, it could be due to two issues: either two or more keypads share the same address, or the DS7430 or DS7433 is installed in the wrong pins. To resolve this, ensure the keypad jumper is correctly installed in the back of each keypad and verify that the DS7430 or DS7433 is properly installed.
General| Partitions | 8 |
|---|---|
| Communication | PSTN, IP |
| Battery Backup | 7Ah |
| Operating Temperature | 0°C to 49°C (32°F to 120°F) |
| Power Supply | AC 16.5V, 25VA |
Guides for turning the system on and arming it using keypad commands.
Lists commands for accessing various system features and functions.
Details enclosure size, operating temperature, zones, keypads, partitions, and users.
Specifies power input, auxiliary power, outputs, max load currents, and backup battery calculation.
Step-by-step instructions for installing the enclosure and control/communicator unit.
Diagrams and explanations for connecting control terminals and system hardware layout.
Guides on identifying alarms, silencing, and responding to emergencies.
Procedures for performing zone, battery, communicator, and fire walk tests.
How to enter programmer mode, read, and enter program addresses and values.
Programming zone functions, types, outputs, partitions, and keypad assignments.
Configuring delays, reports, phone numbers, and pager settings.
Common issues with keypads, reporting, zones, and their solutions.
Troubleshooting power, communication, bus, and general system faults.
