Bostitch N62FN User Manual

N52FN/N62FN
INDUSTRIAL OIL FREE ANGLED FINISH NAILERS
CLAVADORA INDUSTRIAL EN BARRA ANGULA LIBRE DE LUBRICACIÓN
CLOUEURS INDUSTRIEL DE FINITION EN BANDES SANS HUILE
107740REVD 12/00
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURI-
Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA
PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON SU REPRESEN-
DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX AVERTISSE-
GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI VOUS AVEZ DES
QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE CONCESSIONNAIRE BOSTITCH.
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
Stanley Fastening Systems

Bostitch N62FN Specifications

General

Brand	Bostitch
Model	N62FN
Category	Nail Gun
Language	English

Summary

Limited Warranty

Safety Instructions

Tool Specifications

Fastener Specifications

Details nail series, gauge, wire size, and fastener range for N52FN and N62FN.

Tool Air Fitting

Specifies the 1/4" N.P.T. male plug and required inside diameter for the tool.

Operating Pressure

Defines the recommended operating pressure range for optimal fastener performance.

Air Consumption

Outlines the air consumption rates for N52FN and N62FN models at 60 fasteners/min.

Air Supply and Connections

Fittings

Instructions for installing a quick-disconnect male plug on the tool.

Hoses

Specifies minimum working pressure rating for air hoses.

Supply Source

Emphasizes using clean, regulated compressed air, not other gases.

Regulator

Details the requirement for a pressure regulator and its operating range.

Filter

Explains the importance of filters for tool performance and maintenance.

Loading the N52FN/N62FN

Loading Nails

Instructions for inserting strips of nails into the magazine.

Engaging Pusher

How to pull the pusher guide to engage the nails.

Removing Fasteners

Method to depress the pusher tab and slide it forward.

Adjusting the Multi-directional Exhaust

Instructions for rotating the exhaust deflector to a desired position.

Tool Operation

Trigger Operation

Describes the single-action fastener drive by pulling the trigger.

Contact Trip Operation

Explains operation using the contact trip in conjunction with the trigger.

Sequential Trip Operation

Details operation requiring contact trip engagement before trigger pull.

Tool Operation Check

Procedures to verify correct operation for trigger, contact, and sequential modes.

Maintaining the Pneumatic Tool

Replacement Parts

Recommends using genuine Bostitch replacement parts.

Air Supply-Pressure and Volume

Discusses the importance of adequate air volume and pressure for tool function.

Trouble Shooting

Dial-A-Depth Fastener Control Adjustment

Jam Release

Instructions for disconnecting air supply before clearing a jammed fastener.

Jam Clearing

Steps to disconnect air, relieve fasteners, and release the latch assembly.

Partial Release Of Magazine

Procedure to slide the magazine to the rear of the tool to clear jams.

Full Release Of Magazine

Instructions for pulling the latch upward and rotating the assembly.

Magazine Assembly Removal

Steps to slide the magazine assembly off the tool.

Accessories Available