EasyManua.ls Logo

Bostitch N71C - User Manual

Bostitch N71C
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
N71C
COIL-FED PNEUMATIC NAILER
CLAVADORA NEUMÁTICA ALIMENTADA POR ROLLO
CLOUEUR PNEUMATIQUE À ENROULEMENT
165359REVB 8/05
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI
VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE
CONCESSIONNAIRE BOSTITCH.
STANLEY FASTENING SYSTEMS L.P.

Table of Contents

Questions and Answers

  • H
    harrisfrancisAug 12, 2025
    Why is my Bostitch N71C lacking power and cycling slowly?
    • C
      Cody ButlerAug 12, 2025
      The Bostitch Nail Gun might be performing weakly or cycling slowly due to several reasons: * It may need lubrication, so use BOSTITCH Air Tool Lubricant. * A broken cylinder cap spring could be the culprit, requiring a replacement. * The O-rings/seals might be cut or cracked, necessitating their replacement. * The exhaust could be blocked; inspect the bumper, head valve spring, and muffler. * A worn or leaky trigger assembly might need replacement. * Dirt or tar buildup on the driver requires disassembling the nose/driver for cleaning. * Incorrectly seated cylinder sleeve on the bottom bumper requires disassembly for correction. * A dry head valve needs disassembly and lubrication. * Low air pressure requires checking the air supply equipment.
  • S
    Samantha ChangAug 19, 2025
    What to do if fasteners jam in my Bostitch N71C?
    • K
      kyle94Aug 19, 2025
      If fasteners are jamming in your Bostitch Nail Gun, consider these potential causes: * A worn driver channel might require replacing the nose and checking the door. * Using the wrong size fasteners means you should only use recommended fasteners. * Bent fasteners should be discontinued. * Loose canister or nose screws should be tightened. * A broken or chipped driver should be replaced.
  • A
    alvarezmarcusAug 23, 2025
    Why won't my Bostitch N71C Nail Gun cycle?
    • M
      michael24Aug 25, 2025
      If your Bostitch Nail Gun fails to cycle, it could be due to: * Air supply restriction: Check the air supply equipment. * Lack of lubrication: Use BOSTITCH Air Tool Lubricant. * Worn head valve O-rings: Replace the O-rings. * Broken cylinder cap spring: Replace the cylinder cap spring. * Head valve stuck in cap: Disassemble, check, and lubricate.
  • S
    Stephanie PriceAug 27, 2025
    How to fix air leak from the frame or cap of my Bostitch N71C?
    • K
      Kenneth JonesAug 27, 2025
      If your Bostitch Nail Gun's frame or cap is leaking air, the issue might be: * A damaged gasket or seal, in which case you should replace it. * A cracked or worn head valve bumper, which means you should replace the bumper. * Loose cap screws, so tighten and recheck them.
  • B
    bblackAug 31, 2025
    What to do if my Bostitch N71C frame/nose leaks air?
    • F
      fritztammyAug 31, 2025
      If the frame or nose of your Bostitch Nail Gun is leaking air: * Check for loose nose screws and tighten them. * Inspect for a cut or cracked O-ring or gasket and replace if necessary. * Examine the bumper for cracks or wear and replace it if needed.
  • C
    Cody GarciaSep 3, 2025
    How to fix air leak from the trigger valve stem of my Bostitch N71C Nail Gun?
    • J
      jared14Sep 3, 2025
      If the trigger valve stem of your Bostitch Nail Gun leaks air, it is likely due to cut or cracked O-rings/seals. Replace the trigger valve assembly to resolve this.
  • R
    Richard LeeSep 7, 2025
    How to fix air leak from the trigger valve housing of my Bostitch N71C Nail Gun?
    • V
      Victoria HuynhSep 7, 2025
      If the trigger valve housing of your Bostitch Nail Gun is leaking air, the O-ring might be cut or cracked. Replace the O-ring to solve the problem.
  • K
    Kevin JamesNov 15, 2025
    What to do if my Bostitch N71C Nail Gun is skipping fasteners and has intermittent feed?
    • J
      Joshua CostaNov 15, 2025
      If your Bostitch Nail Gun is skipping fasteners, consider the following: * A worn bumper might be the problem, so replace it. * Tar or dirt in the driver channel requires disassembling and cleaning the nose and driver. * Air restriction or inadequate airflow through the quick disconnect socket and plug means you should replace the quick disconnect fittings. * A worn piston O-ring requires replacing the O-ring and checking the driver. * Lack of lubrication means you should use BOSTITCH Air Tool Lubricant. * A damaged feed piston spring requires replacing the spring. * Low air pressure means you should check the air supply system to the tool. * Loose canister nose screws require tightening all screws. * Fasteners that are too short or the wrong size require using only reco...

Bostitch N71C Specifications

General IconGeneral
BrandBostitch
ModelN71C
CategoryNail Gun
LanguageEnglish

Related product manuals