Bostitch N79RH User Manual

OPERATION and MAINTENANCE MANUAL
MANUAL DE OPERACIÓN Y DE MANTENIMIENTO
MANUEL D’INSTRUCTIONS ET D’ENTRETIEN
117526REVB 9/04
BEFORE OPERATING THIS TOOL, ALL OPERATORS SHOULD STUDY THIS MANUAL TO
UNDERSTAND AND FOLLOW THE SAFETY WARNINGS AND INSTRUCTIONS. KEEP THESE
INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS,
CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR.
ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERÁN ESTUDIAR
ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE
SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA
HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNÍQUESE CON
SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR.
LIRE ATTENTIVEMENT LE PRÉSENT MANUEL AVANT D’UTILISER L’APPAREIL. PRÉTER UNE
ATTENTION TOUTE PARTICULIÈRE AUX CONSIGNES DE SÉCURITÉ ET AUX
AVERTISSEMENTS. GARDER CE MANUEL AVEC L’OUTIL POUR FUTUR RÉFÉRENCE. SI
VOUS AVEZ DES QUESTIONS, CONTACTEZ VOTRE REPRÉSENTANT OU VOTRE
CONCESSIONNAIRE BOSTITCH.
STANLEY FASTENING SYSTEMS
N79RH
PNEUMATIC STICK NAILERS
CLAVADORA NEUMÁTICA ALIMENTADA POR BARRA
CLOUEUR PNEUMATIQUE EN BANDES

Bostitch N79RH Specifications

General

Brand	Bostitch
Model	N79RH
Category	Nail Gun
Language	English

Summary

Introduction and Warranty Information

Introduction

Provides an overview of the tool and the importance of the manual.

Limited Warranty

Outlines the warranty terms, coverage, and limitations for the tool.

Safety Instructions

Air Supply and Connections Safety

Details requirements for air supply, fittings, hoses, and regulators for safe tool operation.

Loading Tool Safety

Provides step-by-step instructions and safety precautions for loading fasteners into the tool.

General Tool Operation Safety

Explains the general principles and safety aspects of operating the pneumatic tool.

Tool Maintenance Safety

Offers initial guidance on tool maintenance and safety considerations.

Tool Specifications and Operation Modes

Tool Specifications Overview

Lists technical specifications for the N79PT/N90PT models, including dimensions and actuation.

Fastener and Air Fitting Specifications

Details compatible nail sizes, shank diameters, and required air fitting type.

Operating Pressure and Air Consumption

Recommends optimal operating pressure and explains air volume requirements.

Operation Modes

Introduces the two types of operation: Contact Trip and Sequential Trip.

Air Supply, Lubrication, and Cold Weather Operation

Air Supply and Connections Details

Details air supply, fittings, hoses, regulators, and filters for optimal tool performance.

Lubrication Guidelines

Provides guidance on proper lubrication for optimal performance and longevity.

Cold Weather Operation Precautions

Recommends specific lubricants and precautions for operation in cold weather.

Loading the N79PT/N90PT

Loading Procedure

Step-by-step instructions for opening the magazine, loading nails, and closing.

Fastener Depth Control Adjustment

Explains how to adjust the fastener depth for desired countersink or flush drive.

Tool Operation

Contact Trip Operation

Details how to operate the tool using Single Fastener Placement or Rapid Fastener Operation.

Sequential Trip Operation

Explains the sequence for driving fasteners with the sequential trip mechanism.

Tool Operation Check and General Safety

Operation Check Procedure

Provides steps to verify correct operation of Contact Trip and Sequential Trip modes.

General Safe Operation Guidelines

Lists additional warnings for safe use, including avoiding misuse and proper handling.

Pneumatic Tool Maintenance and Air Supply

Pneumatic Tool Maintenance

Provides guidance on maintaining the tool, including caution with springs and replacement parts.

Air Supply-Pressure and Volume

Explains the importance of air volume and pressure for tool performance and troubleshooting.

Trouble Shooting Guide

Troubleshooting Leaks and Cycle Failures

Addresses common problems like air leaks, trigger issues, and failure to cycle with causes and corrections.

Troubleshooting Power and Feed Issues

Covers lack of power, slow cycling, skipping fasteners, and jamming with causes and corrections.

Driver Maintenance and Accessories

Directional Exhaust Deflector Adjustment

Instructions on adjusting the directional exhaust deflector for desired exhaust direction.

Driver Maintenance Instructions

Guidance on worn drivers, redressing, and length adjustment for optimal nail drive.

Available Accessories

Lists various Bostitch accessories available for the tool, such as lubricants and conversion kits.