Broadcom NetXtreme II SERIES User Manual

Linux Driver Software: Broadcom NetXtreme II® Network Adapter User Guide
file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/linux.htm[9/5/2014 3:45:01 PM]
tar xvzf netxtreme2-version.tar.gz
2. Build the driver bnx2.ko (or bnx2i.ko) as a loadable module for the running kernel:
cd netxtreme2-version
make
3. Test the driver by loading it (first unload the existing driver, if necessary):
rmmod bnx2 (or bnx2x, or bnx2i)
insmod bnx2/src/bnx2.ko (or bnx2x/src/bnx2x.ko, or bnx2i/src/bnx2i.ko)
Verify that your network adapter supports iSCSI by checking the message log. If the message "bnx2i: dev eth0
does not support iSCSI" appears in the message log after loading the bnx2i driver, then iSCSI is not supported. This
message may not appear until the interface is opened, as with:
ifconfig eth0 up
4. Load the cnic driver (if applicable):
insmod cnic.ko
5. Install the driver and man page:
make install
NOTE: See the RPM instructions above for the location of the installed driver.
6. Install the user daemon (brcm_iscsiuio).
Refer to Load and Run Necessary iSCSI Software Components for instructions on loading the software components required to
use the Broadcom iSCSI offload feature.
To configure the network protocol and address after building the driver, refer to the manuals supplied with your operating
system.
Installing the Binary DKMS RPM Driver Package
Dynamic Kernel Module Support (DKMS) is designed to simplify the rebuilding of modules whenever you upgrade the kernel.
This is accomplished by creating a framework where a kernel-dependent module source can reside.
To install the binary DKMS RPM driver package
1. Download the binary DKMS RPM (dkms-version.noarch.rpm) from http://linux.dell.com/dkms/.
2. Install the binary DKMS RPM package:
rpm -ivh dkms-version.noarch.rpm
3. Install the DKMS RPM driver package:
rpm -ivh netxtreme2-version dkms.noarch.rpm
Verify that your network adapter supports iSCSI by checking the message log. If the message "bnx2i: dev eth0
does not support iSCSI" appears in the message log after loading the bnx2i driver, then iSCSI is not supported. This
message may not appear until the interface is opened, as with:
ifconfig eth0 up
4. To use Broadcom iSCSI, refer to Load and Run Necessary iSCSI Software Components to load the necessary software
components.
For more information, go to http://linux.dell.com.
Installing the Binary KMOD/KMP Driver Package
To install the binary KMOD/KMP driver package
1. Install the KMOD/KMP RPM driver package:
SUSE: rpm -ivh broadcom-netxtreme2-kmp-[kernel]-version.x86_64.rpm
Red Hat: kmod-kmp-netxtreme2-{kernel]-version.x86_64.rpm
Verify that your network adapter supports iSCSI by checking the message log. If the message "bnx2i: dev
eth0 does not support iSCSI" appears in the message log after loading the bnx2i driver, then iSCSI is not
supported. This message may not appear until the interface is opened, as with:
ifconfig eth0 up
2. To use Broadcom iSCSI, refer to Load and Run Necessary iSCSI Software Components to load the necessary software
components.

Broadcom NetXtreme II SERIES Specifications

General

Brand	Broadcom
Model	NetXtreme II SERIES
Category	Network Card
Language	English