Brother DCP-7060D Basic User's Guide

12
27 Note that some telephones are not compatible with this unit and dialling errors may result if the
two devices are used together in other than quiet conditions. The Telecom Faults Service is
not to be called should such problems arise. In such cases, it is recommended that the prefix
and wanted number are dialled manually.
28 This equipment may not provide for the effective hand-over of a call to another device
connected to the same line.
29 This equipment is not capable, under all operating conditions, of correct operation at the higher
speeds for which it is designed. Telecom will accept no responsibility should difficulties arise
in such circumstances. This condition typically applies to 56 kbit/s modems and facsimile
products operating at >14.4 kbit/s.
30 When using the Caller Line Identification incorporated in this device, verify the integrity of the
recorded digits prior to dialling.
31 Some parameters required for compliance with Telecom’s Telepermit requirements are
dependent on the equipment (PC) associated with this device. The associated equipment shall
be set to operate within the following limits for compliance with Telecom’s Specifications:
 There shall be no more than 10 call attempts to the same number within any 30 minute
period for any single manual call initiation, and
 The equipment shall go on-hook for a period of not less than 30 seconds between the end
of one attempt and the beginning of the next call attempt.
 Automatic calls to different numbers are spaced such that there is not less than 5 seconds
between the end of one call attempt and the beginning of another.
 Equipment shall be set to ensure that calls are answered within 3 and 30 seconds of the
receipt of ringing.
32 In the event of any problem with this device, it is to be disconnected, and a CPE item connected
to one of its terminal ports may be connected directly in its place. The user should then arrange
for the product to be repaired. Should the matter be reported to Telecom as a wiring fault and
the fault is proven to be due to this product, a call out charge will be incurred by the customer.
33 The caller ID telephone numbers that are displayed and stored in this equipment include the
caller’s area code but not the toll access “0” prefix. When calling back it is necessary to add a
“0“ to the telephone number, or if the telephone number is a local number, omit the area code
digit. If the toll services of a service provider other than Telecom are being used then a toll
charge may be incurred if the “0” prefix toll access code and area code are used.
34 To reduce the risk of fire, electric shock and injury to people, note the following:
 DO NOT use this product near appliances that use water, a swimming pool or in a wet basement.
 DO NOT use the product during an electrical storm (there is the remote possibility of an
electrical shock) or to report a gas leak (MFC only) in the vicinity of the leak.
 DO NOT use this product in the vicinity of a gas leak.
IMPORTANT NOTICE A
Under power failure conditions, this telephone may not operate. Please ensure that a separate
telephone, not dependent on local power, is available for emergency use in emergencies.

Brother DCP-7060D Specifications

General

Dimensions (WxDxH)	405 x 399 x 268 mm
All-in-one functions	Copy, Print, Scan
Color all-in-one functions	Scan
Print technology	Laser
Maximum resolution	2400 x 600 DPI
Economical printing	Yes
Time to first page (black, normal)	9 s
Print speed (black, normal quality, A4/US Letter)	24 ppm
Duplex print speed (black, normal quality, A4/US Letter)	5 ppm
Digital sender	No
Maximum duty cycle	- pages per month
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
N-in-1 copy function (N=)	2, 4
Time to first copy (black, normal)	11 s
Copy speed (black, normal quality, A4)	24 cpm
Scan to	E-mail, Image, OCR
Scanner type	Flatbed scanner
Grayscale levels	256
Input color depth	48 bit
Output color depth	24 bit
Scan speed (black)	2.63 ppm
Image formats supported	BMP, JPG, TIF
Maximum scan resolution	19200 x 19200 DPI
Optical scanning resolution	600 x 2400 DPI
Total input capacity	250 sheets
Total output capacity	100 sheets
Multi-Purpose tray input capacity	1 sheets
Custom media width	76.2 - 216 mm
Maximum print size	216 x 406 mm
Custom media length	116 - 406.4 mm
Paper tray media types	Bond paper, Plain paper, Recycled paper
Paper tray media weight	60 - 105 g/m²
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5, B6
Multi-purpose tray media types	Bond paper, Envelopes, Heavyweight paper, Plain paper, Recycled paper
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	60 - 163 g/m²
Display	LCD
Market positioning	Home & office
Display number of lines	2 lines
Display number of characters	16
Standard interfaces	USB 2.0
USB 2.0 ports quantity	1
Processor family	ARM
Sound power level (standby)	30 dB
Sound pressure level (printing)	53 dB
AC input frequency	50 - 60 Hz
Power consumption (standby)	55 W
Power consumption (PowerSave)	0.9 W
Power consumption (average operating)	445 W
Sustainability certificates	ENERGY STAR
Package weight	13.200 g
Mac operating systems supported	Mac OS X 10.4 Tiger, Mac OS X 10.5 Leopard, Mac OS X 10.6 Snow Leopard
Windows operating systems supported	Windows 2000 Professional, Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 7 Professional, Windows 7 Professional x64, Windows 7 Ultimate, Windows 7 Ultimate x64, Windows Vista Business, Windows Vista Business x64, Windows Vista Home Basic, Windows Vista Home Basic x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows Vista Ultimate, Windows Vista Ultimate x64, Windows XP Home, Windows XP Home x64, Windows XP Professional, Windows XP Professional x64