EasyManua.ls Logo

Brother MFC-8950DW - User Manual

Brother MFC-8950DW
198 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Basic User’s Guide
MFC-8950DW
MFC-8950DWT
Not all models are available in all countries.
Version 0
USA/CAN

Table of Contents

Other manuals for Brother MFC-8950DW

Questions and Answers

  • B
    briana71Sep 4, 2025
    Why does my Brother All in One Printer say 'Access Denied'?
    • J
      janetwilliamsSep 4, 2025
      If your Brother All in One Printer shows 'Access Denied,' it means the function you're trying to use is restricted by Secure Function Lock 2.0. Contact your administrator to check your Secure Function Lock Settings.
  • J
    John RamirezAug 25, 2025
    What to do if my Brother All in One Printer says 'No Toner'?
    • C
      Calvin RileyAug 25, 2025
      If your Brother All in One Printer displays a 'No Toner' error, it means that either the toner cartridge or the drum unit and toner cartridge assembly is not installed correctly. To resolve this, remove the drum unit and toner cartridge assembly, then remove the toner cartridge from the drum unit, and re-install the toner cartridge back into the drum unit. Re-install the drum unit and toner cartridge assembly back in the machine. If the problem continues, replace the toner cartridge.
  • L
    Lisa McphersonAug 25, 2025
    Why will my Brother All in One Printer not turn on?
    • T
      Timothy RussellAug 26, 2025
      If your Brother All in One Printer will not turn on, adverse conditions on the power connection, such as lightning or a power surge, may have triggered the machine’s internal safety mechanisms. Turn the machine off and unplug the power cord. Wait for ten minutes, then plug in the power cord and turn the machine on.
  • K
    Kristin JohnsSep 12, 2025
    Why does my Brother All in One Printer say 'Too Many Files'?
    • H
      haley54Sep 12, 2025
      The 'Too Many Files' message on your Brother All in One Printer indicates that there are too many files stored on the USB Flash memory drive. Reduce the number of files stored on the USB Flash memory drive.
  • G
    gdelgadoSep 22, 2025
    What to do if my Brother All in One Printer says 'Incorrect or expired ID'?
    • J
      jbarnettSep 22, 2025
      If your Brother All in One Printer displays 'Incorrect or expired ID', it means the temporary ID you entered is incorrect. The solution is to enter the correct temporary ID. Also, a temporary ID is valid for 24 hours, so if it has expired, apply for Brother Web Connect access again to receive a new temporary ID, and then use the new ID to register the account to the machine.
  • K
    Kristen HammondSep 8, 2025
    How to fix 'Cooling Down Wait for a while' error on Brother All in One Printer?
    • D
      dbraySep 8, 2025
      The 'Cooling Down Wait for a while' message on your Brother All in One Printer indicates that the drum unit or toner cartridge is too hot, causing the machine to pause. Ensure you can hear the fan spinning inside the machine and that the exhaust outlet is not blocked. If the fan is working, remove any obstructions around the exhaust outlet and allow the machine to cool down for several minutes while it remains turned on. If the fan isn't spinning, disconnect the machine from the power for a few minutes, then reconnect it.
  • H
    Heidi JohnsonSep 1, 2025
    How to fix Brother Software when I cannot communicate with my Brother machine using SSL?
    • S
      Susan MosesSep 1, 2025
      To communicate with your Brother machine using SSL, ensure you obtain a valid certificate and install it on both your machine and computer. Also, verify that the port setting of your machine is correct. You can confirm your machine’s port setting on the Web Based Management screen by clicking Network, Protocol, and then HTTP Server Settings.
  • N
    Nicholas BaileySep 23, 2025
    Why Authentication/Encryption methods are not supported by Brother All in One Printer?
    • A
      Ann HughesSep 23, 2025
      If your Brother All in One Printer does not support the authentication/encryption methods used by your wireless access point/router, for infrastructure mode, change the authentication and encryption methods of the wireless access point/router. Your printer supports WPA, WPA2, OPEN and Shared key authentication methods. WPA supports TKIP or AES encryption methods. WPA2 supports AES for the encryption method. OPEN and Shared key correspond to WEP encryption. For ad-hoc mode, the printer supports OPEN authentication method only, with optional WEP encryption.
  • S
    shallSep 15, 2025
    What does 'Size mismatch' mean on my Brother All in One Printer and how to fix it?
    • V
      vpageSep 15, 2025
      The 'Size mismatch' message on your Brother All in One Printer indicates that the paper in the tray is not the correct size. Load the correct size of paper in the tray and set the size of paper to the tray.
  • V
    Veronica TorresAug 28, 2025
    What does 'Replace Parts Drum Unit' mean on my Brother MFC-8950DW All in One Printer?
    • S
      Sheila WilcoxAug 28, 2025
      The 'Replace Parts Drum Unit' message on your Brother All in One Printer indicates that it is time to replace the drum unit. Replace the drum unit.

Brother MFC-8950DW Specifications

General IconGeneral
Typeall in one
Colorblack
Tray Capacity500
Automatic Document Feeder Capacity50 sheets
Paper Sizeletter, legal, executive, a4, a5, a6, b5, b6, custom sizes from 3" x 5" to 8.5" x 14"
Paper Handlingup to 500 sheets
Mono Print Speed42 pages per minute
Print Resolution Monoup to 1200 x 1200
Maximum Number of Pages Per Monthup to 100, 000
Scanner Typeflatbed
Scan Resolutionup to 19200 x 19200
Fax Functionyes
Cartridgestn-720, tn-750, tn-780, dr-720
Number Of Cartridges2
Internal Memoryyes
Networkwired, wireless
Connectivityusb 2.0
OS Compatibilitywindows or mac os
Mobile Devices Connectionyes
Weight and Dimensions IconWeight and Dimensions
Height19.3 inches
Width16.3 inches
Net Weight39 pounds

Related product manuals