Brother MFC-J280W Manual

Appendix A
16
A
Using ARP to configure the IP address A
If you are unable to use the BRAdmin application and your network does not use a DHCP server, you can
also use the ARP command. The ARP command is available on Windows
®
systems that have TCP/IP
installed as well as UNIX systems. To use ARP enter the following command at the command prompt:
arp -s ipaddress ethernetaddress
ping ipaddress
Where ethernetaddress is the MAC Address (Ethernet Address) of the print server and ipaddress is
the IP address of the print server. For example:
 Windows
®
systems
Windows
®
systems require the dash “-” character between each digit of the MAC Address (Ethernet
Address).
arp -s 192.168.1.2 00-80-77-31-01-07
ping 192.168.1.2
 UNIX/Linux
®
systems
Typically, UNIX and Linux
®
systems require the colon “:” character between each digit of the MAC Address
(Ethernet Address).
arp -s 192.168.1.2 00:80:77:31:01:07
ping 192.168.1.2
Note
You must be on the same Ethernet segment (that is, there cannot be a router between the print server and
operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP address.
If your administrator has configured the system to deliver IP addresses using BOOTP, DHCP or RARP
your Brother print server can receive an IP address from any one of these IP address allocation systems.
In which case, you will not need to use the ARP command. The ARP command only works once. For
security reasons, once you have successfully configured the IP address of a Brother print server using the
ARP command, you cannot use the ARP command again to change the address. The print server will
ignore any attempts to do this. If you wish to change the IP address again, use a Web Based Management
(web browser), TELNET (using the SET IP ADDRESS command) or factory reset the print server (which
will then allow you to use the ARP command again).

Brother MFC-J280W Specifications

General

Dimensions (WxDxH)	404 x 378 x 160 mm
All-in-one functions	Copy, Fax, Print, Scan
Connectivity technology	Wired & Wireless
Color all-in-one functions	copy, fax, print, scan
Duplex printing	No
Print technology	Inkjet
Maximum resolution	6000 x 1200 DPI
Print speed (black, normal quality, A4/US Letter)	33 ppm
Print speed (color, normal quality, A4/US Letter)	26 ppm
Printing colors	Black, Cyan, Magenta, Yellow
Maximum duty cycle	2500 pages per month
Number of print cartridges	4
Copier resize	25 - 400 %
Maximum copy resolution	- DPI
N-in-1 copy function (N=)	2, 4
Copy speed (black, normal quality, A4)	22 cpm
Copy speed (color, normal quality, A4)	20 cpm
Scan to	E-mail, File, Image, OCR
Scanner type	Flatbed scanner
Input color depth	36 bit
Maximum scan area	A4 / Letter (216 x 297) mm
Image formats supported	BMP, JPG, PCX, PNG, TIF
Maximum scan resolution	19200 x 19200 DPI
Optical scanning resolution	1200 x 2400 DPI
Faxing	Color faxing
Fax memory	170 pages
Modem speed	14.4 Kbit/s
Auto reduction	Yes
Fax transmission speed	7 sec/page
Total input capacity	100 sheets
Total output capacity	50 sheets
Envelopes sizes	10, DL
Maximum print size	216 x 356 mm
Paper tray media types	Envelopes, Glossy paper, Photo paper, Plain paper
Non-ISO print media sizes	Executive
ISO A-series sizes (A0...A9)	A4
Photo paper sizes (imperial)	4x6, 5x7, 5x8, 8x10 \
Display	LCD
Display diagonal	1.9 \
Market positioning	Home & office
Standard interfaces	USB 2.0, Wireless LAN
USB 2.0 ports quantity	1
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Sound pressure level (copying)	50 dB
AC input voltage	100 - 120 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	4 W
Power consumption (average operating)	29 W
Package weight	10300 g
Operating temperature (T-T)	50 - 95 °F
Operating relative humidity (H-H)	20 - 80 %
Sustainability certificates	ENERGY STAR