How to unlock a Brother Electronic Keyboard P-touch screen?
If the screen 'locks' or your Brother Electronic Keyboard P-touch isn't responding normally, reset the internal memory to the initial settings. If this doesn't solve the problem, disconnect the AC adapter and remove the batteries for more than 10 minutes.
What to do if the Brother P-touch D450 Label Maker does not print correctly?
If your Brother Label Maker isn't printing correctly, try removing the tape cassette and reinstalling it, pressing firmly until it clicks. If the print head is dirty, clean it using a cotton swab or an optional print head cleaning cassette (TZe-CL4).
What to do if my Brother P-touch D450 doesn't print?
If the Brother Label Maker isn't printing after you press the Print key, ensure that you've entered text and that the tape cassette is correctly installed with enough tape. If the tape is creased, cut off the damaged section and thread the tape through the exit slot. If there's a jam, remove the cassette, carefully pull out the jammed tape, and cut it. Make sure the tape end goes through the guide before reinstalling the cassette.
How to fix a Brother P-touch D450 that prints incorrectly?
If the Brother Label Maker is not printing labels correctly, remove the tape cassette and firmly reinstall it until it clicks into place. If the print head is dirty, clean it using a cotton swab or an optional print head cleaning cassette (TZe-CL4).
What does 'Cutter Malfunction' mean on my Brother Electronic Keyboard?
The 'Cutter Malfunction' message on your Brother Electronic Keyboard indicates that the tape cutter was closed when you tried to print or feed tape. To resolve this, turn the P-touch off and then on again. If tape is tangled in the cutter, remove it.
What does 'Check # of digits entered' mean on Brother Electronic Keyboard?
The 'Check # of digits entered' message on your Brother Electronic Keyboard means that the number of digits entered in the barcode data does not match the number of digits set in the barcode parameters. Enter the correct number of digits.
How do I find out the firmware version number for my Brother P-touch Label Maker?
The version number and other information for the firmware can be confirmed by pressing the following keys: 1. Press ( ). 2. Select [ ??] using or, and then press ( ) or ( ). 3. Select [ ????] using or, and then press ( ) or ( ).
Why does my Brother Label Maker say 'Label Too Long!'?
If your Brother Label Maker is displaying 'Label Too Long!', it means the label length, based on the text you've entered, exceeds 1 meter. To resolve this, edit the text to shorten the label or use a shorter text.
What to do if the ink ribbon is separated from the ink roller in Brother P-touch D450 Label Maker?
If the ink ribbon is broken, replace the tape cassette. Otherwise, leave the tape uncut, remove the tape cassette, and wind the loose ink ribbon onto the spool.
What does 'Cutter Malfunction!' mean on my Brother P-touch?
If the Brother P-touch displays 'Cutter Malfunction!', turn the P-touch off and then on again before continuing. If tape is tangled in the cutter, remove the tape.
Explains safety warnings and cautions to prevent injury and damage.
Provides general advice for using the P-touch and handling labels.
Lists carton contents and initial setup.
Details the P-touch's display and keyboard layout and functions.
Instructions for AC adapter connection and battery installation.
Guides on correctly inserting the tape cassette.
Procedures for powering the device on and off.
Describes the procedure for feeding the tape.
How to adjust LCD contrast and backlight settings.
Overview of creating labels directly or via PC connection.
Instructions for typing, editing text, and managing lines/blocks.
How to insert various symbols and special characters.
Adjusting font, size, alignment, and other character properties.
Instructions on how to add decorative frames to labels.
Covers setting label length, margins, and tab settings.
Guides on using predefined templates and layouts for labels.
Instructions for creating labels using block-based layouts.
Explains how to create labels with barcodes, including parameters.
Procedures for modifying or removing barcode elements from labels.
How to check the label layout before printing.
Basic instructions for printing labels and cutting them.
How to print one or multiple copies of a label.
Instructions for sequential numbering or lettering on labels.
How to print labels in mirror image for specific applications.
Options for cutting labels, like margins and auto-cut.
How to fine-tune the printed label length.
How to print labels stored in the device's collection.
How to save created labels for later use.
Procedures for printing, opening, or deleting saved label files.
How to reset the device to factory settings or clear data.
Instructions for cleaning the exterior of the P-touch.
How to clean the print head for better print quality.
Guidance on cleaning the tape cutter mechanism.
Common problems and their solutions for the P-touch.
Explains specific error messages and how to resolve them.
Technical details and specifications of the P-touch device.
Lists the operating system and hardware requirements for software.
General| Model | Brother P-touch D450 |
|---|---|
| Device Category | Label Maker |
| Print Method | Thermal Transfer |
| Print Resolution | 180 dpi |
| Print Speed | 20 mm/sec |
| Maximum Print Width | 24 mm |
| Max. Label Length | 1 m |
| Keyboard | QWERTY |
| Multi-block Printing | Yes |
| Memory | Yes |
| Cutter | Manual |
| Label Width | 3.5, 6, 9, 12, 18 mm |
| Tape Sizes | 3.5 mm, 6 mm, 9 mm, 12 mm, 18 mm |
| Tape Type | Laminated |
| Tape Compatibility | Brother TZe tape |
| Display | 16 characters |
| Styles | Bold, Italic, Underline, Shadow |
| Power Source | AC Adapter or Batteries |
To Next Page