To Next PageTo Next PageWhy are label files saved previously missing from my Brother Label Maker?
All files saved in the internal memory of your Brother Label Maker are deleted if the batteries are weak or the AC adapter is disconnected for more than two minutes.
What to do if the ink ribbon is separated from the ink roller in Brother P-touch D450 Label Maker?
If the ink ribbon is broken, replace the tape cassette. Otherwise, leave the tape uncut, remove the tape cassette, and wind the loose ink ribbon onto the spool.
What to do if the Brother Label Maker stops while printing a label?
If your Brother P-touch label maker stops during printing, it could be due to a couple of reasons. If you see striped tape, it means you've reached the end of the tape, and you should replace the tape cassette. Alternatively, try replacing all the batteries or connecting the AC adapter directly to the P-touch.
What does 'Cutter Malfunction!' mean on my Brother P-touch?
If the Brother P-touch displays 'Cutter Malfunction!', turn the P-touch off and then on again before continuing. If tape is tangled in the cutter, remove the tape.
What does 'Check # of digits entered' mean on my Brother Label Maker?
If the number of digits entered in the barcode data does not match the number of digits set in the barcode parameters on your Brother Label Maker, enter the correct number of digits.
Why is the display blank on my Brother Label Maker?
If your Brother Label Maker display remains blank after turning it on, check that the batteries are correctly installed and that the AC adapter (designed for your Label Maker) is properly connected. Also, ensure that the rechargeable battery is fully charged.
Why does my Brother P-touch D450 stop printing mid-label?
If the Brother Label Maker stops while printing, it could be due to the tape running out (indicated by striped tape). In this case, replace the tape cassette. Alternatively, the batteries may be low. Try replacing all the batteries or connecting the AC adapter directly to the Label Maker.
What to do if the screen ‘locks’ or the Brother P-touch Label Maker does not respond normally?
If the screen ‘locks’ or the Brother P-touch does not respond normally, reset the internal memory to the initial settings. If resetting the P-touch does not solve the problem, disconnect the AC adapter and remove the batteries for more than 10 minutes.
What to do if the Brother Label Maker display remains blank after turning it on?
If the display remains blank after turning on the Brother Label Maker, verify that the batteries are correctly installed and that the AC adapter (designed specifically for your device) is properly connected. Also, ensure the rechargeable battery is fully charged.
How to fix a Brother P-touch D450 that prints incorrectly?
If the Brother Label Maker is not printing labels correctly, remove the tape cassette and firmly reinstall it until it clicks into place. If the print head is dirty, clean it using a cotton swab or an optional print head cleaning cassette (TZe-CL4).
General| Model | Brother P-touch D450 |
|---|---|
| Device Category | Label Maker |
| Print Method | Thermal Transfer |
| Print Resolution | 180 dpi |
| Print Speed | 20 mm/sec |
| Maximum Print Width | 24 mm |
| Max. Label Length | 1 m |
| Keyboard | QWERTY |
| Multi-block Printing | Yes |
| Memory | Yes |
| Cutter | Manual |
| Label Width | 3.5, 6, 9, 12, 18 mm |
| Tape Sizes | 3.5 mm, 6 mm, 9 mm, 12 mm, 18 mm |
| Tape Type | Laminated |
| Tape Compatibility | Brother TZe tape |
| Display | 16 characters |
| Styles | Bold, Italic, Underline, Shadow |
| Power Source | AC Adapter or Batteries |
Explains safety warnings and cautions to prevent injury and damage.
Provides general advice for using the P-touch and handling labels.
Lists carton contents and initial setup.
Details the P-touch's display and keyboard layout and functions.
Instructions for AC adapter connection and battery installation.
Guides on correctly inserting the tape cassette.
Procedures for powering the device on and off.
Describes the procedure for feeding the tape.
How to adjust LCD contrast and backlight settings.
Overview of creating labels directly or via PC connection.
Instructions for typing, editing text, and managing lines/blocks.
How to insert various symbols and special characters.
Adjusting font, size, alignment, and other character properties.
Instructions on how to add decorative frames to labels.
Covers setting label length, margins, and tab settings.
Guides on using predefined templates and layouts for labels.
Instructions for creating labels using block-based layouts.
Explains how to create labels with barcodes, including parameters.
Procedures for modifying or removing barcode elements from labels.
How to check the label layout before printing.
Basic instructions for printing labels and cutting them.
How to print one or multiple copies of a label.
Instructions for sequential numbering or lettering on labels.
How to print labels in mirror image for specific applications.
Options for cutting labels, like margins and auto-cut.
How to fine-tune the printed label length.
How to print labels stored in the device's collection.
How to save created labels for later use.
Procedures for printing, opening, or deleting saved label files.
How to reset the device to factory settings or clear data.
Instructions for cleaning the exterior of the P-touch.
How to clean the print head for better print quality.
Guidance on cleaning the tape cutter mechanism.
Common problems and their solutions for the P-touch.
Explains specific error messages and how to resolve them.
Technical details and specifications of the P-touch device.
Lists the operating system and hardware requirements for software.
