To Next PageTo Next PageWhat to do if the display is blank on my Brother Electronic Keyboard?
If the display on your Brother Electronic Keyboard remains blank after turning it on, first, check that the batteries are correctly installed and the AC adapter (designed exclusively for your P-touch) is properly connected. Also, ensure that the rechargeable battery is fully charged.
Why does my Brother Electronic Keyboard P-touch stop while printing?
Your Brother Electronic Keyboard P-touch may stop printing because you've reached the end of the tape. If you see striped tape, replace the tape cassette. Alternatively, the batteries may be low, so replace them or connect the AC adapter directly to the P-touch.
How do I check the firmware version on my Brother P-touch?
To find out the version number of the firmware for your Brother P-touch, press the following keys: 1. Press ( ). 2. Select [Settings] using or, and then press ( ) or ( ). 3. Select [Version information] using or, and then press ( ) or ( ).
Why are my saved label files missing from my Brother P-touch D450?
If files saved previously on your Brother Label Maker are missing, it is possible that all files saved in the internal memory were deleted because the batteries were weak or the AC adapter was disconnected for more than two minutes.
Why does my Brother Label Maker say 'Label Too Long!'?
If your Brother Label Maker is displaying 'Label Too Long!', it means the label length, based on the text you've entered, exceeds 1 meter. To resolve this, edit the text to shorten the label or use a shorter text.
How do I find out the firmware version number for my Brother P-touch Label Maker?
The version number and other information for the firmware can be confirmed by pressing the following keys: 1. Press ( ). 2. Select [ ??] using or, and then press ( ) or ( ). 3. Select [ ????] using or, and then press ( ) or ( ).
What to do if the Brother P-touch D450 Label Maker does not print after pressing the Print key?
If the Brother Label Maker doesn't print after pressing the Print key, first ensure that you've entered text and that the tape cassette is correctly installed with sufficient tape. Additionally, if the tape is creased, cut off the creased section and thread the tape through the tape exit slot. In case of a tape jam, remove the tape cassette, pull out the jammed tape and cut it, ensuring the end of the tape passes through the tape guide before reinstalling the cassette.
What does it mean when the Brother P-touch D450 Label Maker displays the error message: ????????
This error message indicates that there is no conversion candidate. Please confirm the text inputted and transform again.
What does it mean when the Brother P-touch D450 displays the error message: ?????
This error message indicates that there is no conversion candidate. Please confirm the text inputted and transform again.
What does it mean when the Brother Label Maker displays the error message: ??????# ??!
This error message indicates that the number of digits entered in the barcode data does not match the number of digits set in the barcode parameters. Enter the correct number of digits.
General| Model | Brother P-touch D450 |
|---|---|
| Device Category | Label Maker |
| Print Method | Thermal Transfer |
| Print Resolution | 180 dpi |
| Print Speed | 20 mm/sec |
| Maximum Print Width | 24 mm |
| Max. Label Length | 1 m |
| Keyboard | QWERTY |
| Multi-block Printing | Yes |
| Memory | Yes |
| Cutter | Manual |
| Label Width | 3.5, 6, 9, 12, 18 mm |
| Tape Sizes | 3.5 mm, 6 mm, 9 mm, 12 mm, 18 mm |
| Tape Type | Laminated |
| Tape Compatibility | Brother TZe tape |
| Display | 16 characters |
| Styles | Bold, Italic, Underline, Shadow |
| Power Source | AC Adapter or Batteries |
Explains safety warnings and cautions to prevent injury and damage.
Provides general advice for using the P-touch and handling labels.
Lists carton contents and initial setup.
Details the P-touch's display and keyboard layout and functions.
Instructions for AC adapter connection and battery installation.
Guides on correctly inserting the tape cassette.
Procedures for powering the device on and off.
Describes the procedure for feeding the tape.
How to adjust LCD contrast and backlight settings.
Overview of creating labels directly or via PC connection.
Instructions for typing, editing text, and managing lines/blocks.
How to insert various symbols and special characters.
Adjusting font, size, alignment, and other character properties.
Instructions on how to add decorative frames to labels.
Covers setting label length, margins, and tab settings.
Guides on using predefined templates and layouts for labels.
Instructions for creating labels using block-based layouts.
Explains how to create labels with barcodes, including parameters.
Procedures for modifying or removing barcode elements from labels.
How to check the label layout before printing.
Basic instructions for printing labels and cutting them.
How to print one or multiple copies of a label.
Instructions for sequential numbering or lettering on labels.
How to print labels in mirror image for specific applications.
Options for cutting labels, like margins and auto-cut.
How to fine-tune the printed label length.
How to print labels stored in the device's collection.
How to save created labels for later use.
Procedures for printing, opening, or deleting saved label files.
How to reset the device to factory settings or clear data.
Instructions for cleaning the exterior of the P-touch.
How to clean the print head for better print quality.
Guidance on cleaning the tape cutter mechanism.
Common problems and their solutions for the P-touch.
Explains specific error messages and how to resolve them.
Technical details and specifications of the P-touch device.
Lists the operating system and hardware requirements for software.
