Brother QL-1060N User Manual (English)

Other manuals for Brother QL-1060N

Network User's Guide42 pages

Service Manual121 pages

User Guide42 pages

Setup & Operation Guide121 pages

Questions and Answers:

B
Bryce HouseAug 18, 2025
How to fix Brother QL-1060N Label Maker when it does not print?
- K
  Karen Key MDAug 18, 2025
  If the Brother Label Maker QL-1060N does not print or shows a printing error, first, ensure the USB/Ethernet cable is securely connected. Next, check if the DK Roll is correctly installed; if not, remove and reinstall it. Also, verify that there is enough roll remaining and that the DK Roll compartment cover is closed. If the issue persists, try turning the Brother QL-1060N off and on again.
R
Rita KingAug 21, 2025
Why are labels jamming in my Brother Label Maker cutter?
- J
  jamesgrahamAug 21, 2025
  If labels are jammed in the cutter or not ejected correctly after printing with your Brother Label Maker, it may be due to dirt or lint on the roller preventing it from rolling freely.
P
Paula AndersonAug 23, 2025
Why is the power button not lit on my Brother QL-1060N Label Maker?
- M
  Michael BowenAug 23, 2025
  If the power button on your Brother Label Maker is not lit, first ensure that the power cord is correctly plugged into the device and the electrical outlet. If it is, try plugging it into another electrical outlet to rule out any issues with the current outlet.
E
Emma ScottAug 26, 2025
How to reset Brother QL-1060N Label Maker and delete transferred data?
- S
  Scott HuntAug 26, 2025
  To reset the Brother Label Maker and delete the data transferred from your PC, turn OFF the printer. Then, press the ON/OFF button and the CUT button six times. This will delete all transferred data and reset the machine to its factory settings.
P
Philip RochaAug 28, 2025
Why does my Brother QL-1060N Label Maker print labels with streaks?
- E
  Erica SmithAug 28, 2025
  If the printed label from your Brother Label Maker has streaks or poor-quality characters, it might be due to a dirty print head or roller. While the print head usually stays clean with normal use, lint or dirt from the roller may stick to it. Clean the roller to resolve this issue.
A
Angela JensenAug 30, 2025
What to do if a data transmission error appears on my Brother Label Maker?
- M
  maria45Aug 30, 2025
  If you encounter a data transmission error on your computer while using the Brother QL-1060N, first ensure that you have selected the correct port in the Printer Properties dialog box under the “Print to the following port” list. Also, check if the QL-1060N is in cooling mode, indicated by the LED lamp flashing orange; if so, wait until it stops before attempting to print again. Finally, if other users are printing large amounts of data over the network, wait until their jobs are completed before reattempting your print job.
K
kristimckeeSep 2, 2025
What to do if I get a cutter error on my Brother QL-1060N Label Maker?
- M
  michelle98Sep 2, 2025
  If a cutter error occurs on your Brother Label Maker, keep the DK roll compartment cover closed and press the ON/OFF button. The cutter will move back to its normal position, and the machine will turn OFF automatically. After the machine turns OFF, inspect the cutter unit and remove any paper jam.
J
jasonmartinezSep 4, 2025
Why can't my scanner read the barcode printed by my Brother QL-1060N Label Maker?
- N
  Natasha BrownSep 4, 2025
  If the printed barcode from your Brother Label Maker cannot be read, it may be due to the type of print scanner being used. Try using a different scanner. It's recommended to print the barcode with the print setting set to prioritize quality. Also, position the label vertically to the print head as illustrated.
V
Vanessa MyersSep 7, 2025
How to cancel a print job on my Brother QL-1060N Label Maker?
- E
  Emily WhiteSep 7, 2025
  To cancel the current printing job on your Brother Label Maker, ensure that the printer is ON, and then press the ON/OFF button.
K
Kyle RaySep 9, 2025
Why is P-touch Add-In icon missing in Microsoft Word for my Brother QL-1060N Label Maker?
- P
  Paula MasonSep 10, 2025
  If the icon of P-touch Add-In is not displayed on Microsoft® Word, check if Microsoft® Word is started from Microsoft® Outlook®. Also verify if Microsoft® Word is chosen for the editor usually used for Microsoft® Outlook®. If so, quit Microsoft® Outlook®, and restart Microsoft® Word.

Brother QL-1060N Specifications

General

Print technology	Direct thermal
Vertical printing	Yes
Maximum resolution	300 x 300 DPI
Maximum print height	3000 mm
Maximum printing width	98.6 mm
Wi-Fi	No
Standard interfaces	USB 2.0, RS-232
USB 2.0 ports quantity	1
Tape type	DK
Tape cutting	-
Internal memory	2 MB
Number of fonts	7
Number of styles	6
Built-in barcodes	CODABAR (NW-7), Code 128 (A/B/C), Code 39, Code-128 Codabar Library, Code-39 Library, EAN128, EAN13, EAN8, Interleaved 2/5, ITF, PDF417
Compatible operating systems	Windows 2000/XP/Vista/7/8 (32 & 64 bits version)\\r Windows Server 2003/2008 (R2)/2012\\r Mac OS 10.3.9 - 10.8
Tape size	62 mm
Dimensions (WxDxH)	170 x 220 x 148 mm
Bundled software	P-touch Editor, P-touch Address Book
Maximum label width	102 mm
Maximum label length	3 m
Product color	Grey, Metallic