What to do if the label is not ejected correctly from my Brother Label Maker?
If labels are not ejected correctly after printing with your Brother Label Maker, first check that the Label Output Slot isn't blocked. Then, remove and reinstall the DK Roll to ensure it's set correctly. Finally, make sure the DK Roll Compartment Cover is closed properly.
What to do if Brother Label Printer print quality is poor?
Check if there is dirt or lint on the roller preventing it from rolling freely.
What to do if Brother Label Printer status LED is not lit?
Ensure that the AC Power Cord is properly inserted into the Label Printer. If it is, try plugging it into a different AC power outlet.
What to do if data transmission error appears on Brother Label Printer?
Verify that the correct port is selected in the Printer Properties dialog box under the "Print to the following port" list. Also, check if the Label Printer is in cooling mode, indicated by the Status LED flashing orange; if so, wait until it stops before printing again.
How to fix cutter error on Brother Label Printer?
If a cutter error occurs, keep the DK Roll Compartment Cover closed and press the Power Button. The cutter will return to its normal position, and the Label Printer will turn off automatically. Once off, inspect the label outlet and remove any jammed labels.
What to do if Brother QL-600 Label Maker printed label has streaks or poor quality characters?
Check if the Print Head or roller is dirty. Lint or dirt from the roller may stick to the Print Head. If this happens, clean the roller.
How to reset an error on a Brother QL-600 Label Maker?
To reset an error on your Brother Label Maker: 1. Open and then close the DK Roll Compartment Cover. 2. If the error persists, press the Cut Button or the Feed Button. 3. If the error still isn't resolved, turn the Label Printer off and then on again. 4. If the error continues, contact Brother Customer Service.
What to do if my Brother Label Maker is not printing?
If your Brother Label Maker isn't printing or you're getting a printing error, make sure the USB cable is securely connected. Also, remove the DK Roll and then reinsert it, ensuring there's enough roll left. Verify the DK Roll Compartment Cover is properly closed. Try turning the label printer off and on. If using a USB hub, connect the printer directly to the computer or try a different USB port. If the issue continues, consult your Brother dealer.
General| Print Technology | Direct thermal |
|---|---|
| Maximum Label Width | 62 mm |
| Connectivity | USB |
| Cutter | Automatic |
| Resolution | 300 dpi |
| Power Supply | AC adapter |
| Operating Temperature | 10°C to 35°C |
| Compatible Label Types | Die-cut labels, Continuous length labels |
| Maximum Print Speed | 44 labels per minute |
General disclaimers and important notes about the manual's content and product.
Information on where to find other related manuals for the product.
Explains symbols indicating hazardous situations that could result in death or serious injury.
Explains symbols indicating hazardous situations that could result in minor or moderate injuries.
Explains symbols indicating information or directions that should be followed to avoid damage or failed operations.
Explains symbols indicating notes that provide helpful information for better understanding and use.
Specific safety and handling precautions for DK rolls, including thermal paper and film.
Details the physical components and controls of the label printer.
Step-by-step instructions for connecting the printer to a power source.
Instructions on how to properly insert a DK roll into the printer.
Procedures for powering the label printer on and off.
Guide for installing necessary software and drivers on a computer.
Instructions on how to establish a connection between the printer and a computer.
Overview of the printing process from a computer using the printer.
Steps for designing and printing custom labels using computer software.
Guidance on how to properly attach printed labels to surfaces.
Instructions for installing software and drivers without an internet connection.
Using the dedicated tool to configure printer settings on Windows.
Using the dedicated tool to configure printer settings on macOS.
Specific instructions for using P-touch Editor on Windows operating systems.
Specific instructions for using P-touch Editor on macOS.
Overview of the printing process from within P-touch Editor.
Using the Snap mode to capture and save screen content.
Steps to launch and begin using the P-touch Address Book software.
Description of the main layout window and its components in the Address Book.
Step-by-step process for adding a new contact entry.
Instructions to open and start using the P-touch Library application.
Guide on how to open and modify existing label templates.
Procedures for printing label templates managed by P-touch Library.
How to find specific label templates within the P-touch Library.
Instructions for updating specific P-touch software applications on Windows.
Guide for updating the printer's internal firmware to the latest version.
Procedures for resetting printer settings using the physical buttons.
How to reset printer settings using the software tool on a computer.
Instructions for cleaning the outer casing of the label printer.
Guidance on cleaning the slot where labels exit the printer.
Explanation of the automatic print head cleaning process.
General guidance on identifying and resolving common printer issues.
Solutions for issues encountered during printer driver installation on Windows.
Understanding the meaning of different LED light patterns on the printer.
Common issues and solutions related to the printing process.
General steps for resetting errors on the label printer.
Solutions for when printed barcodes are not recognized by scanners.
How to check the current firmware and software versions.
Detailed technical specifications of the label printer hardware.
Recommended temperature and humidity ranges for printer operation.
Configuring the printer driver settings for direct printing from Windows applications.
Configuring basic print options like paper size and quality in the driver.
Configuring advanced graphic and formatting options in the driver.
General guidance on printing from various Windows applications.
To Next Page
