To Next PageTo Next PageWhat to do if my Brother S-6200A Sewing Machine displays error E130?
If your Brother Sewing Machine displays error code E130, first, ensure that the 4-pin motor connector inside the control box is securely connected. If the issue persists, check if the sewing machine has locked up by manually turning the machine pulley. If it doesn't turn easily, there may be a problem with the control box, and it might need replacement.
What to do if my Brother S-6200A displays error E701?
If you see the error code E701 on your Brother Sewing Machine, first, ensure that the power supply voltage matches the control box voltage specifications. Also, check if the power supply voltage is abnormally high. If the problem persists, there may be an issue with the control box, and it might need replacement.
What to do if my Brother S-6200A Sewing Machine is skipping stitches?
If you're experiencing skipped stitches while sewing with your Brother Sewing Machine: * Check the needle: Replace the needle if the tip is bent or broken. * Needle installation: Install the needle correctly if it is not. * Threading: Thread the machine correctly if it is not. * Presser foot pressure: Adjust the presser foot pressure. * Needle thickness: Replace the needle with a thicker one if it is too thin. * Presser foot height: Adjust the height of the presser foot. * Thread take-up spring: Adjust the tension of the thread take-up spring. * Needle and rotary hook timing: Adjust the height of the needle bar and the clearance between the needle and the tip of the rotary hook.
Why is there a large degree of puckering on my Brother S-6200A?
If you're experiencing a large degree of puckering (excess tension) with your Brother Sewing Machine: * Upper thread tension: Weaken the upper thread tension as much as possible. * Lower thread tension: Weaken the lower thread tension as much as possible. * Needle condition: Replace the needle if it is blunt. * Needle thickness: Use as thin a needle as possible. * Thread take-up spring: Reduce the thread take-up spring tension as much as possible and lower its position as much as possible. * Presser foot pressure: Adjust the presser foot pressure. * Sewing speed: Gradually reduce the maximum sewing speed. * Feed dog angle: Tilt the front of the feed dog down slightly.
What to do if my Brother S-6200A Sewing Machine does not operate when power is on?
If the power supply connector is disconnected from the control box, insert the connector securely.
Why am I getting skipped stitches at the start of sewing with my Brother Sewing Machine?
If you experience skipped stitches or thread unravelling at the sewing start with your Brother Sewing Machine: * Thread take-up spring tension: Reduce the tension. * Thread take-up spring range: Lower the position. * Upper thread length: Adjust the pretension. * Thread trimming: Sharpen or replace the knives. * Needle thickness: Use a thinner needle. * Bobbin thread length: Replace the anti-spin spring if the bobbin spins loosely. * Sewing speed: Enable slow start. * Needle stop position: Adjust the needle up stop position.
Why are loops appearing in the seam of my Brother S-6200A?
If you notice loops appearing in the seam of your Brother Sewing Machine, polish the thread path with a fine-grain file or sandpaper to make it smoother. Also, check the bobbin to ensure it's turning smoothly; pull out the lower thread to check for slackness, or replace the bobbin or bobbin case.
Why is the seam uneven on my Brother S-6200A Sewing Machine?
If your Brother Sewing Machine is showing an uneven seam, adjust the presser foot pressure. Also, adjust the feed dog height. If the bobbin is scratched, smooth it or replace it.
How to fix lower thread if it is not tight on Brother S-6200A Sewing Machine?
If the lower thread is not tight on your Brother Sewing Machine, adjust the lower thread tension or upper thread tension.
How to fix upper thread if it is not tight on Brother S-6200A?
If the upper thread is not tight on your Brother Sewing Machine, adjust the upper thread tension or lower thread tension. Also, advance the needle timing.
General| Type | Industrial Sewing Machine |
|---|---|
| Lubrication | Automatic |
| Free Arm | No |
| Maximum Stitch Length | 4 mm |
| Application | Apparel |
| Stitch Length | 4mm |
| Needle | DB x 1 |
| Presser Feet | Standard Presser Foot |
