BROVIND CFF Series User Manual

PG.
33
SUMMARY MENU
MENU
DESCRIPTION
CFF / DCFF
CFV
2
Vibration Amplitude
. . or . .
. . or . .
3
Frequency
.  (33 Hz; 50 Hz; 100
Hz)
. . (20÷140 Hz)
4
Tracking or Calibrated Tracking
Not available
.  (0=Normal loop; 1 =.
Calibrated tracking loop)
4/1
Autocalibration
Not available
.  (0=Off; 1 =On)
5
Integrator Gain
. . (1; 2; 4; 8)
. . (1; 2; 4; 8)
6
Sensor 1 (Sensor 3 for vibr.2 DCFF)
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
6/1
Sensor 1: Light/Dark (S3 vibr.2 DCFF)
−.  (-S1=0=Light; -
S1=1=Dark)
−.  (-S1=0=Light; -
S1=1=Dark)
6/2
Sensor 1: Delay ON (S3 vibr. 2 DCFF)
. . (Da 0 sec. A 25,5
sec)
. . (Da 0 sec. A 25,5
sec)
6/3
Sensor 1: Delay OFF (S3 for vibr. 2 DCFF)
. . (Da 0 sec. A 25,5
sec)
. . (Da 0 sec. A 25,5
sec)
7
Sensor 2 (Sensor 4 for vibr. 2 DCFF)
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
7/1
Sensor 2: Light or Dark (S4 for vibr. 2 DCFF)
−.  (-S1=0=Light; -
S1=1=Dark)
−.  (-S1=0=Light; -
S1=1=Dark)
7/2
Sensor 2: Delay ON (S4 for vibr. 2 DCFF)
. . ( 0 sec. A 25,5 sec)
. . ( 0 sec. A 25,5 sec)
7/3
Sensor 2: Delay OFF (S4 for vibr. 2 DCFF)
. . ( 0 sec. A 25,5 sec)
. . ( 0 sec. A 25,5 sec)
8
0 – 10 Volts
−. (0=Off; 1 =On)
−. (0=Off; 1 =On)
8/1
0 – 10 Volts: Light or Dark
−. =Direct
−. =Denied
−. =Direct
−. =Denied
9
Synchronism
Only with MASTER board
Only with MASTER board
10
Probe
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
10/1
K.Probe Value
.  typical
.  typical
10/2
Filter
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
11
1A, 2A, 3A
See Pg. 21
See Pg. 21
12
Emergency
Only with MASTER board
Only with MASTER board
13
Correction % Synchronism
Only with MASTER board
Only with MASTER board
14
Calibration
. . Amax value
. . Amax value
14/1
Calibration from fixed point (0-10V)
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
14/2
Full calibration
Not available
.  (0=Off; 1 =On)
15
Output relay
  State relay
  Actuator control
  MASTER only
  Balance
  Elevator. DCFF only
  Unit. DCFF only
  State relay n.1
  Actuator control
  MASTER only
  Balance
  (Null)
  (Null)
  State Relay n. 2
16
Maximum current
Not available
. . =Max value
17
Simultaneous stop of two vibrators
.  DCFF Only
Not available
17/1
Synchronism of DCFF1 and DCFF2
.  DCFF Only
18
A max (No SRV02)
..
..
18/1
A0 setting with 1000 step
 (0=Off; 1 =On)
 (0=Off; 1 =On)
19
Ramp. Soft-Start and Soft-Stop
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
19/1
Ramp. Times
.  e . 
.  e . 
20
A0 setting as default parameter
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
21
Pieces-counter setting as default parameter


24
Internal temperature
°..
°..
25
Resonance frequency
. . Only after calibration
. . Only after calibration
26
Pieces-counter function: Display
. Visual. Counter
Not available
26/1
Pieces-counter function: Display
 Visual. Totalizer
Not available
26/2
Pieces-counter function: Display
 Reset totalizer
Not available
27
Pieces- counter function: Setting
  Set pieces-counter
Not available
27/1
Pieces-counter function: Setting
  Intermediate reset
Not available
27/2
Pieces-counter function: Setting
 Intermediate threshold
 Intermediate threshold
27/3
Pieces-counter function: Setting
 Pieces to count
 Pieces to count
28
Time Out function
.. (0=Off; 1 =On)
.. (0=Off; 1 =On)
28/1
Time Out function: Selecting sensor
.  S1, S2, (S3, S4)
.  S1, S2
28/2
Time Out function: Setting time
.  (30 – 250)
.  (30 – 250)
MENU
DESCRIPTION
CFF/DCFF
CFV
30
Default: Reset inspection parameters
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
31
Reset controller
.  (0=Off; 1 =On)
.  (0=Off; 1 =On)
34
Motor function
.  (0=Off; 1=On)
Not available
34/1
Motor function: Toggle
.  (0=Off; 1=On)
Not available

BROVIND CFF Series Specifications

General

Brand	BROVIND
Model	CFF Series
Category	Controller
Language	English