BROVIND DCFF Series User Manual

Name: BROVIND DCFF Series
Brand: BROVIND
Rating: 5 (1 reviews)

35 pages

To Next Page

To Previous Page

PG.

CONNECTION DIAGRAM

Fig. 7

ATTENTION:

It is good practice not to remove power to the electronic card to stop the vibrator, but use a remote

control input IN1 or IN2

Table of Contents2
Ce" Compliance Statement4
Personal Safety Rules5
General Description5
Cff Series6
Dcff Series6
Cfv Series6
Technical Data7
Layout8
Machine Identification Plate8
Inspection9
Installation9
CONNECTION DIAGRAM for CFF and CFV10
Connection Diagram for Dcff11
Connection Diagram for Cff15A12
Connection Diagram for Cff10A 400V12
Display Board13
Controlling the Vibrator with Remote Potentiometer14
On/Off Vibrator with External Command 0-24 Vpg14
Special Applications: Balance Function15
Special Applications: Elevator Function16
Special Applications: Discharge Unit Function17
Special Applications: Alarm-Related Relay17
Pieces Counter Function17
Programming Boolean Functions18
Setting Instructions and Menu19
Menu 2 Changing Vibration Amplitude20
Menu 3 Changing Frequency20
Menu 4 Calibrated Tracking20
Menu 5 Integrator Gain21
Menu 6: Assigning Sensor Px121
Menu 7: Assigning Sensor Px221
MENU 8 EXTERNAL COMMAND 0-10 V / 4-20 Ma21
Menu 9 Synchronizing Multiple Vibrators21
Menu 10 Automatic Running Mode with Srv02 Probe21
Menu 11 Pre-Set Acceleration Value 1A22
Menu 11/1 Pre-Set Acceleration Value 2A22
Menu 11/2 Pre-Set Acceleration Value 3A22
Menu 12 Emergency22
Menu 13 Correcting Synchronism22
Menu 14 Automatic Calibration of Vibrator22
Menu 15 Output Relays24
Menu 16 Maximum Current Value24
Menu 17: Simultaneous Stop of both Vibrators, Link to24
Menu 18: A-Max Setting Without Srv0225
Menu 19 Soft-Start and Soft-Stop Ramp25
Menu 20 A0 Setting as Default Parameter25
Menu 21 Pieces-Counter Setting as Default Parameter25
Menu 24 Internal Temperature25
Menu 25 Vibrator Resonance Frequency and Condition Sensors/Relais25
Menu 26 Pieces-Counter Function - Display26
Menu 27 Pieces-Counter Function - Settings26
Menu 28 Time-Out Function26
Menu 30: Resume Factory-Set Parameters27
Menu 31: Resetting Board27
Menu 34 Motor Function27
Menu 35 Hf/Lf Mode27
Menu 37 : VI Setting for the Calibration Procedure28
Menu 40 Saving Work Configurations28
Menu 41: Load Work Configurations28
Menu 45: Programming a Logic Functions28
Menu 46: Programming B Logic Functions29
Menu 47: Programming C Logic Functions29
Menu 48: Programming D Logic Functions29
Menu 50 Set Communication and Board Address (Rs-485)29
Menu 52 Communication Errors on Bus Rs48529
Menu 59 Bootloader Enable for Firmware Updating30
Menu 60: Board Software Version30
Menu 61: Display Software Version30
Menu 70: Full Password for Changing Parameters30
Menu 71: Partial Password for Changing Parameters30
Menu 81 Open \ Closed Loop30
Srv02 Probe31
Specifications for Operating a Solenoid Valve31
Management in Network31
Maintenance31
Troubleshooting31
Summary Menu33
Notes35

Questions and Answers:

Need help?

Do you have a question about the BROVIND DCFF Series and is the answer not in the manual?

BROVIND DCFF Series Specifications

General

Brand	BROVIND
Model	DCFF Series
Category	Controller
Language	English

Related product manuals

BROVIND DCFF Series User Manual

Table of Contents

Questions and Answers:

BROVIND DCFF Series Specifications

Related product manuals