EasyManua.ls Logo

Bryant 350MAV User Manual

Bryant 350MAV
44 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
NOTE: Read the entire instruction manual before starting the
installation.
This symbol indicates a change since the last issue.
TABLE OF CONTENTS
SAFETY CONSIDERATIONS.....................................................1
INTRODUCTION..........................................................................2
Codes and Standards......................................................................4
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........4
APPLICATIONS............................................................................4
General ......................................................................................4
Upflow Applications.................................................................4
Downflow Applications............................................................6
Horizontal Left (Supply-Air Discharge) Applications ............7
Horizontal Right (Supply-Air Discharge) Applications ..........9
LOCATION..................................................................................11
General ....................................................................................11
Furnace Location Relative to Cooling Equipment ................12
Hazardous locations................................................................12
INSTALLATION.........................................................................12
Leveling Legs (If Desired).....................................................12
Installation in Upflow and Downflow Applications..............13
Installation in Horizontal Applications ..................................14
Air Ducts.................................................................................14
Filter Arrangement..................................................................15
Bottom Closure Panel.............................................................16
Gas Piping...............................................................................17
Electrical Connections ............................................................17
Direct Venting.........................................................................19
Condensate Drain....................................................................28
Sequence of Operation............................................................31
START-UP PROCEDURES........................................................33
General ....................................................................................33
Prime Condensate Trap With Water......................................33
Purge Gas Lines......................................................................34
Adjustments.............................................................................34
Check Safety Controls............................................................38
Checklist..................................................................................39
SAFETY CONSIDERATIONS
Installing and servicing heating equipment can be hazardous due to
gas and electrical components. Only trained and qualified person-
nel should install, repair, or service heating equipment. Untrained
personnel can perform basic maintenance functions such as clean-
ing and replacing air filters. All other operations must be per-
formed by trained service personnel. When working on heating
equipment, observe precautions in literature, on tags, and on labels
attached to or shipped with unit and other safety precautions that
may apply.
Follow all safety codes. In the United States, follow all safety
codes including the National Fuel Gas Code (NFGC) NFPA
54-1999/ANSI Z223.1-1999 and the Installation Standards, Warm
Air Heating and Air Conditioning Systems (NFPA 90B)
ANSI/NFPA 90B. In Canada, refer to the current edition of the
A93040
Fig. 1—Multipoise Orientations
A93041
UPFLOW
DOWNFLOW
HORIZONTAL
LEFT
AIRFLOW
AIRFLOW
AIRFLOW
AIRFLOW
HORIZONTAL
RIGHT
REGISTERED QUALITY SYSTEM
C
a
r
r
i
e
r
C
o
r
p
o
r
a
t
i
o
n
R
E
G
I
S
T
E
R
E
D
F
I
R
M
I
S
O
9
0
0
1
#
A
2
8
8
3
®
EFFICIENCY
RATING
CERTIFIED
CERTIFIED
Installation, Start-Up,
and Operating Instructions
DELUXE 4–WAY MULTIPOISE
FIXED-CAPACITY DIRECT-VENT
CONDENSING GAS FURNACE
Cancels: II 350M-40-10 II 350M-40-12
10-00
350MAV
Series E &F
—1—

Other manuals for Bryant 350MAV

Questions and Answers:

Bryant 350MAV Specifications

General IconGeneral
TypeGas Furnace
EfficiencyHigh Efficiency
StagesSingle Stage
Ignition SystemHot Surface Ignition
Fuel TypeNatural Gas
Heating Capacity40, 000-120, 000 BTU/h
Ignition TypeHot Surface Ignition
Heat Exchanger MaterialAluminized Steel
AFUE80%
Warranty10-Year Parts

Summary

SAFETY CONSIDERATIONS

INTRODUCTION

Overview of furnace models, their capacities, and certifications.

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS

Procedures to prevent damage to electronic components from static discharge.

APPLICATIONS

Details on furnace installation applications like upflow, downflow, etc.

CODES AND STANDARDS

LOCATION

INSTALLATION

General installation procedures and specific application details.

LEVELING LEGS (IF DESIRED)

Instructions for installing leveling legs on the furnace.

INSTALLATION IN UPFLOW AND DOWNFLOW APPLICATIONS

Procedures for installing the furnace in upflow or downflow configurations.

INSTALLATION IN HORIZONTAL APPLICATIONS

Procedures for installing the furnace in horizontal configurations.

AIR DUCTS

FILTER ARRANGEMENT

Information on installing and selecting air filters for the furnace.

GAS PIPING

ELECTRICAL CONNECTIONS

J-BOX RELOCATION

Instructions for relocating the electrical junction box.

24-V Wiring

Details on making thermostat connections for 24-volt systems.

DIRECT VENTING

Removal of Existing Furnaces from Common Vent Systems

Steps for safely removing a furnace from a common venting system.

COMBUSTION-AIR AND VENT PIPING

Guidelines for installing combustion air and vent piping.

CONDENSATE DRAIN

CONDENSATION DRAIN PROTECTION

Methods to protect the condensate system from freezing.

SEQUENCE OF OPERATION

HEATING MODE

Step-by-step process of the furnace operating in heating mode.

COOLING MODE

Step-by-step process of the furnace operating in cooling mode.

CONTINUOUS BLOWER MODE

Operation of the blower when set to continuous mode.

HEAT PUMP MODE

Furnace operation sequence when integrated with a heat pump.

COMPONENT TEST

Procedure for testing furnace components.

START-UP PROCEDURES

PRIME CONDENSATE TRAP WITH WATER

Instructions for priming the condensate trap before operation.

PURGE GAS LINES

Procedure for purging gas lines and checking for leaks.

Set Gas Input Rate

How to set the correct gas input rate based on altitude.

Set Temperature Rise

How to measure and adjust air temperature rise.

CHECK SAFETY CONTROLS

Check Primary Limit Control

Procedure to test the primary limit control for proper function.

Check Pressure Switch

Procedure to test the pressure switch operation.

CHECKLIST-INSTALLATION

CHECKLIST-START-UP

SERVICE TRAINING

Related product manuals