Bryant CHS072 - User Manual

Questions and Answers

J
jason83Aug 18, 2025
Why does my Bryant CHS072 Heat Pump compressor operate continuously?
- T
  Tyler LunaAug 18, 2025
  If your Bryant Heat Pump compressor runs continuously, it might be due to a dirty air filter, which you should replace. Alternatively, the unit may be undersized for the load, requiring you to decrease the load or increase the unit size. Check if the thermostat is set too low in cooling mode and reset it if needed. A low refrigerant charge could also be the cause, so locate and repair any leaks before recharging the system. Air in the system can also lead to continuous operation; in this case, recover the refrigerant, evacuate the system, and recharge it. Lastly, a dirty or restricted outdoor coil can cause this issue, so clean the coil or remove any restrictions.
M
Michelle SinghAug 21, 2025
How to fix excessive head pressure in Bryant CHS072?
- C
  Christopher GrossAug 21, 2025
  Excessive head pressure in your Bryant Heat Pump can stem from several causes. Check for a dirty outside air or return air filter (if heating) and replace the filter. If cooling, a dirty outdoor coil could be the problem, so clean the coil. An overcharged refrigerant level can also cause this, requiring you to recover the excess refrigerant. Air in the system is another possibility; in this case, recover the refrigerant, evacuate the system, and recharge. Lastly, ensure that the condensing air is not restricted or short-cycling, and correct as necessary.
S
Stacy ParkerAug 31, 2025
What to do if Bryant CHS072 Heat Pump compressor won't start but outdoor fan runs?
- B
  Brenda KaiserAug 31, 2025
  If your Bryant Heat Pump compressor won't start but the outdoor fan runs, it could be due to faulty wiring or loose connections in the compressor circuit; check the wiring and repair or replace as needed. The compressor motor might be burned out, seized, or have an internal overload open; determine the cause and replace the compressor or allow enough time for the internal overload to cool and reset. A defective run/start capacitor, overload, or start relay could also be the issue; determine the cause and replace the compressor. Finally, one leg of the 3-phase power might be dead; replace the fuse or reset the circuit breaker after determining the cause.
J
Jennifer SmithSep 3, 2025
Why is the head pressure too low in my Bryant CHS072 Heat Pump?
- L
  Lindsay ChandlerSep 3, 2025
  Low head pressure in your Bryant Heat Pump can be caused by a low refrigerant charge, so check for leaks, repair them, and recharge the system. Defective compressor scroll plates can also lead to this issue, requiring you to replace the compressor. Additionally, a restriction in the liquid tube may be the cause, so remove the restriction.
M
mark96Sep 7, 2025
What causes excessive suction pressure in Bryant CHS072 Heat Pump?
- A
  Amy EllisSep 7, 2025
  Excessive suction pressure in your Bryant Heat Pump can result from a high heat load; check for the source and eliminate it. Defective compressor scroll plates can also cause this, requiring you to replace the compressor. Another potential cause is an overcharged refrigerant level, in which case you should recover the excess refrigerant.
C
Cody SalinasSep 12, 2025
How to fix a noisy Bryant CHS072 compressor?
- M
  Mary GoodwinSep 12, 2025
  If your Bryant Heat Pump compressor is making excessive noise, it might be rotating in the wrong direction. To resolve this, reverse the 3-phase power leads as described in the Start-Up section.
S
stevensilvaNov 13, 2025
Why won't my Bryant Heat Pump compressor and outdoor fan start?
- C
  craigrossNov 13, 2025
  If the compressor and outdoor fan of your Bryant Heat Pump won't start, it could be due to several reasons. First, there might be a power failure, in which case you should call your power company. It could also be a blown fuse or tripped circuit breaker, so replace the fuse or reset the breaker, identifying the cause. Other potential causes include a defective thermostat, contactor, transformer, control relay, or capacitor, which would need replacement. Insufficient line voltage or incorrect wiring can also be culprits, requiring correction or rewiring. The thermostat setting might be too high, so lower it below room temperature. Finally, tripped high or low pressure switches or freeze-up protection could be the issue; refer to the sections on ‘Excessive head pressure’ and ‘Suction pressur...
T
Tina ZavalaNov 23, 2025
What to do if suction pressure is too low in Bryant CHS072?
- J
  johnblakeNov 23, 2025
  Low suction pressure in your Bryant Heat Pump can be attributed to several factors. A dirty air filter (if in cooling mode) can cause this, so replace the filter. If heating, a dirty or heavily iced outdoor coil might be the issue; clean the outdoor coil and check the defrost cycle operation. A low refrigerant charge is another potential cause, so check for leaks, repair them, and recharge the system. A restricted metering device or low side can also lead to low suction pressure, so remove the source of the restriction. Insufficient indoor airflow (in cooling mode) can be a factor; increase the air quantity and replace the filter if necessary. If the temperature in the conditioned area is too low, reset the thermostat. A restricted field-installed filter drier should be replaced. If the ou...
W
williamadamsNov 27, 2025
Why does my Bryant Heat Pump compressor cycle on and off frequently?
- J
  Jacqueline SmithNov 27, 2025
  If your Bryant Heat Pump compressor cycles more than it should, it could be due to several reasons. The system may have a refrigerant overcharge or undercharge, requiring you to recover the refrigerant, evacuate the system, and recharge it to the nameplate value. A defective compressor could also be the cause, so replace it after determining the reason for failure. Other potential issues include insufficient line voltage, a blocked outdoor coil, a dirty air filter, or a defective run/start capacitor, overload, or start relay; determine the cause and correct or replace the component. A defective thermostat can also cause cycling, so replace the thermostat. Lastly, a faulty outdoor-fan (cooling) or indoor-fan (heating) motor or capacitor, or a restriction in the refrigerant system could be t...