Canon 3100 - Page 9

COPYRIGHT © 2001 CANON INC. CANON CLC1000/1000S/3100 REV.2 MAY 2001 PRINTED IN JAPAN (IMPRIME AU JAPON)
vii
CHAPTER 5 INSTALLATION
I. SELECTING THE SITE ........................... 5-1
II. INSTALLATION ........................................ 5-3
A. Unpacking......................................... 5-3
B. Removing the Fixings, Supplying
Fixing Oil, and Changing the
Voltage Rating (240V North
American Model) .............................. 5-5
C. Supplying Toner ................................ 5-7
D. Supplying Starter ............................5-15
E. Preventing Deformation of
Externals......................................... 5-19
F. Mounting the Belt Retaining Members
........................................................ 5-20
G. Mounting the Developing Bias
Assembly Protection Member......... 5-21
H-1.Installing the Paper Deck for
CLC1000 ........................................ 5-24
H-2.Installing the Paper Deck-H1 .......... 5-31
H-3.Checking the Operation of the
Paper Deck ..................................... 5-33
I. Checking Images and Operations .. 5-35
III. RELOCATING THE MACHINE .............. 5-36
IV. INSTALLING THE ORIGINAL TRAY ...... 5-38
V. INSTALLING THE CONTROL
CARD V ................................................. 5-39
CHAPTER 6 MAINTENANCE AND SERVICING
I. PERIODICALLY REPLACED PARTS ......6-2
II. CONSUMABLES AND DURABLES ........ 6-5
A. By the Copier’s Hard Counter........... 6-5
B. By the Soft Counter in Service
Mode (COUNTER) ............................ 6-7
III. SCHEDULED SERVICING
PROCEDURE .......................................... 6-8
IV. SCHEDULED MAINTENANCE CHART .. 6-9
CHAPTER 7 TROUBLESHOOTING IMAGE FAULTS/MALFUNCTIONS
GUIDE TO TABLES ......................................... 7-1
I. MAINTENANCE AND SERVICING ......... 7-3
A. Image Adjustment Basic Procedure .... 7-3
B. Scheduled Servicing ............................ 7-5
II. STANDARDS AND ADJUSTMENTS ....... 7-7
A. Image-Related Parts......................... 7-7
B. Original Illuminating System ........... 7-13
C. Photosensitive Drum-Related Parts 7-16
D. Charging Assembly-Related Parts . 7-18
E. Developing Assembly-Related
Parts ............................................... 7-19
F. Transfer Belt Unit ............................ 7-23
G. When Replacing the Pick-Up/
Feeding-Related Parts.................... 7-25
H. Laser Exposure System ................. 7-36
I. Fixing Assembly-Related Parts ...... 7-41
J. Electrical ADJUSTMENT................ 7-42
III. TROUBLESHOOTING IMAGE
PROBLEMS ........................................... 7-52
A. Initial Checks .................................. 7-52
B. Standard Image .............................. 7-53
C. Test Prints ....................................... 7-56
D. Troubleshooting Image Faults .........7-65
IV. TROUBLESHOOTING........................... 7-88
A. Troubleshooting Malfunctions ......... 7-88
V. TROUBLESHOOTING FEEDING
PROBLEMS ......................................... 7-140
A. Jams ............................................. 7-140
B. Feeding Faults .............................. 7-148
VI. ARRANGEMENT AND FUNCTION
OF ELECTRICAL PARTS .................... 7-149
A. Sensors ........................................ 7-150
B. Lamps, Switches, Thermistors,
and Heaters ..................................7-156
C. Clutches........................................ 7-160
D. Solenoids ...................................... 7-162
E. Fans .............................................. 7-164
F. Motors........................................... 7-166
G. PCBs ............................................ 7-168