To Next Page

To Previous Page

305

Option

• Lamp

Part No.: RS-LP08

• Ceiling attachment

Part No.: RS-CL12

(WUX450/WX520)

• Ceiling attachment

Part No.: RS-CL13

(WUX400ST/WX450ST)

• Ceiling-mount pipe

(400 - 600 mm / 15.7 - 23.6 in)

Part No.: RS-CL08*

• Ceiling-mount pipe

(600 - 1000 mm / 23.6 - 39.4 in)

Part No.: RS-CL09*

• Air filter

Part No.: RS-FL02

• Remote control

Part No.: RS-RC06

RS-RC05

• Option feet

Part No.: RS-FT01

* Use the above materials to hang the projector from the ceiling. For details, refer to the

assembly and installation manual provided with the ceiling attachment RS-CL12/RS-CL13.

Default Chapter2
- How to Use this Manual2
  - Copyright Notice3
  - About Trademarks3
- Projector Highlights4
- Quick Reference Guide5
  - Table of Contents6
- Safety Instructions16
  - Safety Precautions17
  - Caution on Hanging from the Ceiling17
- For Safe Use28
Before Use31
- Supplied Accessories32
  - Attaching the Lens Cap (WUX450/WX520)33
- Preparing the Remote Control34
- Part Names37
- Open Source Software46
  - Software under the GPL and LGPL46
  - Software under the GNU General Public License Version 246
Operation49
Projecting an Image51
- Step 1 Turn the Projector on52
- Step 2 Select an Input Signal53
  - Types of Input Signals53
  - Selecting an Input Signal54
- Step 3 Adjust the Image55
- Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen60
- Step 5 Correct the Image Distortion68
  - Adjusting Keystone Distortion68
Table of Contents71
- Step 6 Select the Image Quality (Image Mode)71
  - Image Modes71
    - Selecting an Image Mode72
- Step 7 Set Power-Saving Settings73
- Step 8 Turn the Projector off74
Useful Functions Available During a Presentation75
- Useful Presentation Functions76
- Projecting Images on a USB Flash Drive79
- Split-Screen Display81
Setting Functions from Menus83
- Using Menus84
  - Menu Configuration84
  - Basic Menu Operations85
- Setting Display Status (Input Settings)87
- Adjusting Image Quality (Image Adjustment)96
- Customizing System Operation (System Settings)108
Table of Contents121
- Updating the Firmware121
- Resetting to the Default Setting121
- Checking Projector Information122
Installation and Maintenance123
Installation125
- Before Installation126
  - Precautions When Carrying/Shipping the Projector126
  - Precautions for Installation126
    - When Using Mounted on the Ceiling128
    - Install Facing in the Correct Direction129
- Installation Procedure130
  - Setting up the Projector130
  - Relationship of Image Size to Projection Distance133
    - Amount of Lens Shift134
    - Lens Shift Function134
- Connection Procedure136
- Starting Projection144
  - Starting and Stopping Projection144
  - Changing Notebook Computer Screen Output145
    - Turning on External Monitor Output145
- Installation-Related Menu Settings146
Connecting to a Network167
- Network Connection Overview168
  - Connection Methods168
- Completing Projector Settings169
Table of Contents173
- Viewing the Gateway Address173
- Viewing the MAC Address173
- Enabling/Disabling DHCP174
- Specifying TCP/IP Settings174
- Initializing Network Settings175
- Specifying Pjlink Settings175
- Specifying Use of AMX Device Discovery176
- Specifying Use of Crestron Roomview177
- Completing Computer Settings178
Maintenance197
- Cleaning the Projector198
- Cleaning and Replacing the Air Filter199
  - Replacing the Air Filter199
  - Cleaning the Air Filter200
- Replacing the Lamp201
  - Replacement Lamp202
  - Replacing the Lamp202
    - If the Lamp Cover Comes off204
Networked Multi-Projection (NMPJ)205
Networked Multi-Projection Overview207
- Introduction to Networked Multi-Projection208
- Installing the NMPJ Application210
  - System Requirements210
  - Installation211
    - Uninstallation213
- From Startup to Shutdown215
  - Projection Sessions219
Operation in each Mode221
- Using the Projector in Direct Mode222
  - Procedure222
  - Direct Mode Window224
- Using the Projector in Meeting Mode226
- Using the Projector in Classroom Mode236
- Using the Projector in Broadcast Mode249
  - Procedure249
  - Broadcast Mode Window252
Functions in All Modes255
- Using the Session Selection Menu256
  - Session Selection Menu256
  - Finding Sessions257
- Using the Projector Selection Menu258
  - Projector Selection Menu258
Table of Contents264
- Using Layout Functions264
- Completing Application Projection Settings272
- Reducing Windows to a Compact Size274
- Tips for Better Networked Projection275
- Restrictions276
Appendix277
Appendix279
- Troubleshooting280
  - LED Indicator Meanings280
  - Symptoms and Solutions281
- Relationship between Aspect and Screen Aspect287
- Displayed Test Patterns291
- Supported Signal Types292
- Product Specifications294
- Index302
- Option306
- Menu Configuration306

Brand	Canon
Model	WUX450
Category	Projector
Language	English

Canon WUX450 User Manual

Table of Contents

Other manuals for Canon WUX450

Questions and Answers:

Canon WUX450 Specifications

Related product manuals