Canton Smart Soundbar 9

Other manuals for Canton Smart Soundbar 9

Short Manual52 pages

Questions and Answers

E
Eric BowenDec 1, 2025
How to stop a Canton Smart Soundbar 9 Speaker System Soundbar 9 from buzzing?
- K
  kevinpadillaDec 1, 2025
  If your Canton Soundbar 9 is buzzing, there are several potential causes. First, the signal cables from the source device to the Soundbar 9 might be too long. Try using shorter or higher quality signal cables. Second, the signal cable might not be shielded or the shield is defective. Replace the cable with a shielded and/or higher quality cable. Third, a ground loop may be present. Connect all devices connected to the Soundbar 9 with a safety plug to a power strip. Finally, a non-interference suppressed consumer (e.g. fridge) on the same mains phase could be the cause. Turn off any possible sources of interference for testing purposes, have the relevant device suppressed for interference, or connect the source of interference to another mains phase. You can also insert a special “sheath cu...
P
Patricia BryantAug 25, 2025
How to fix a Canton Speaker System Soundbar 9 that doesn't respond to the remote?
- C
  crystal46Aug 25, 2025
  If your Canton Soundbar 9 isn't responding to the remote control, first, ensure you've removed the protective film from the remote. If that doesn't work, replace the battery, making sure to insert it with the correct polarity.
M
Michael WernerAug 25, 2025
Why is there no playback via Bluetooth on my Canton Speaker System?
- A
  Anna MasonAug 26, 2025
  If you're experiencing no playback via Bluetooth on your Canton Speaker System, there could be several reasons: * Ensure there is a connection between the Soundbar 9 and your mobile device. * If the device is paired but not playing, try reconnecting it. * Set the volume on your mobile device to the maximum. * Increase the volume on the Soundbar 9. * Ensure that there are no sources of interference (such as a WiFi router or laptop) near the Soundbar 9. * If you're using both WiFi and Bluetooth from a mobile device, disable WiFi or reduce the distance between the Soundbar and the mobile device.
S
Stacey BrightAug 27, 2025
What to do if Canton Smart Soundbar 9 Speaker System Soundbar 9 does not turn on?
- D
  Daniel NicholsAug 27, 2025
  If your Canton Speaker System Soundbar 9 doesn't turn on, make sure the mains cable is properly connected to both the power outlet and the Soundbar 9.
M
Michael CarlsonAug 27, 2025
How to increase the volume on my Canton Smart Soundbar 9 Soundbar 9 if the sound reproduction is too soft?
- N
  Nicole RoseAug 27, 2025
  If the sound reproduction on your Canton Speaker System Soundbar 9 is too soft, increase the volume using the “Volume” button, and also increase the volume of the source device. Also, ensure that the maximum possible volume hasn't been limited by the “Volume” function (VOL); if it has, increase the maximum possible volume according to the instructions.
J
Joanna RobinsonSep 15, 2025
How to increase the maximum volume on my Canton Smart Soundbar 9 Speaker System if it is limited to a value less than 70?
- N
  Nicholas BonillaSep 15, 2025
  If the volume on your Canton Speaker System is limited to a value less than 70, it indicates that a maximum volume less than 70 was selected in the Max Volume [VOL] menu. Increase the value according to the instructions in the Max. Volume [VOL] section.
L
Larry JamesSep 13, 2025
What to do if two speakers play the same channel on my Canton Smart Soundbar 9 Speaker System?
- D
  davidhendersonSep 13, 2025
  If two speakers are playing the same channel on your Canton Speaker System, it means two slave speakers were assigned the same channel during pairing. Use the test tone to identify the speaker playing the wrong channel. Then, reconnect this speaker as described in WSP (Wireless Speaker Pairing) and select the correct channel.
S
Stacey RodriguezSep 14, 2025
Why can't an input be selected via the Input buttons on my Canton Smart Soundbar 9 Speaker System?
- S
  Shannon AshleySep 14, 2025
  If an input cannot be selected via the Input buttons on your Canton Speaker System, it's likely that the input was deactivated in the Input Config [INP] menu. Activate the input according to the instructions in the Input Config [INP] section.
W
William VargasSep 6, 2025
Why does Canton Smart Soundbar 9 Speaker System Soundbar 9 unintentionally switch on?
- S
  Shannon KennedySep 6, 2025
  The Canton Soundbar 9 may unintentionally switch on when your mobile device plays system sounds (like keyboard typing), a digital source is turned on, or an analog source is playing. Change the standby function from AUT to ECO, NSB, LAN, or MAN to prevent this.
R
rosarioclaudiaSep 3, 2025
Why does my Canton Smart Soundbar 9 device unintentionally change the input?
- D
  Donna ReevesSep 3, 2025
  If your Canton device unintentionally changes the input, it could be because the Input Select [SEL] function is set to AUT, and the currently selected input AUX (Line) has a long break in playback (over 10 seconds), while a signal is present at another input, or the source device is turned on at the optical and coaxial input. Ensure that no signal is present at any other input during playback at the Line, Balanced and USB inputs, or that a device is switched on at the optical and coaxial digital input. This can also happen when your mobile device issues system sounds; disable these system sounds on your device. Alternatively, set Input Select [SEL] or BT Select function to MAN (manual).

Summary

Safety Instructions

Important Safety Instruction

Unpacking

Connection Terminal

Remote Control

Using Chromecast Built-in

Playback via Bluetooth Wireless Technology

1. Speaker Setup [SPS]

Channel Level [CHL]

Adjusts the volume level of each individual speaker channel in 1dB steps.

Speaker Distance [DST]

Adjusts the distance between speakers and listening position for spatial effect.

Speaker EQ (Equalizer)

Selects three different equalizers for speakers and subwoofer to match room conditions.

Voice Clarity [VOI]

Improves speech intelligibility for better dialogue understanding during films.

2. System Setup [SYS]

IR Menu [IRM]

Manages infrared operation functions, including learning and clearing IR codes.

HDMI CEC [CEC]

Enables or disables HDMI Consumer Electronics Control for device interaction.

Standby Mode [STB]

Configures how the soundbar powers up and down manually or automatically.

Input Configuration [INP]

Sub Output [SUB]

Lipsync [LIP]

Max Volume [VOL]

Factory Reset [RES]

Resets the soundbar to its original factory settings, deleting all custom configurations.

3. Network Setup [NWS]

Network Connection [NWC]

Network Reset [NWR]

4. Wireless Setup [WIS]

Wireless Speaker Pairing [WSP]

Pairs wireless speakers and subwoofers from the Canton Smart Series with the soundbar.

BT Pairing [BTP]

BT Select [BTS]

Troubleshooting

Warranty

Canton Smart Soundbar 9 Specifications

General

Audio decoders	DTS Digital Surround, DTS TruSurround, Dolby Digital
RMS rated power	300 W
Audio output channels	2.1 channels
Audio Return Channel (ARC)	Yes
Tweeter diameter	19 mm
Mid-range driver diameter	50 mm
Tweeter diameter (imperial)	0.75 \
Mid-range driver diameter (imperial)	2 \
Subwoofer type	Passive subwoofer
Cables included	AC, Audio (3.5mm), Coaxial, HDMI, Optical
Receiver included	No
Display type	LED
Certification	CE
Product color	Black
HDMI in	3
HDCP version	2.2
Bluetooth version	4.0
HDMI ports quantity	4
Number of HDMI outputs	1
Connectivity technology	Wired & Wireless
Bluetooth range	10 m
Bluetooth profiles	A2DP
Transmission frequency	2.4 GHz
Apple docking compatibility	Not supported
AC input voltage	100 - 240 V
AC input frequency	50 / 60 Hz
Soundbar power consumption	150 W
Power consumption (standby)	0.4 W