EasyManuals Logo

Carel FCM0002000 User Manual

Carel FCM0002000
35 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
FCM electronic regulator Cod. +302235300 - Rel. 2.0 del 30/11/98
24
P43: Max. duration of defrost
P43 defines the max. duration of a defrost cycle.
Access:
Keypad: if C50=1, 3 or 4 Ü press for 5”;
if C50=0 or 2 Ü the parameter can only be displayed.
Remote control: if C50=0, 1 or 4 Ü press “ENABLE” and and ;
if C50=2 or 3 Ü the parameter can only be displayed.
Modes: only when C00=8
Operating range: from 1 to 60 minutes.
Default: P43 = 1 minute.
Note: if the P41 threshold has been excluded, P43 sets the fixed time for a defrost cycle. When P41 is operative P43 defines the max.
time beyond which the defrost cycle will come to an end; the display will then show a message.
P44: Min. time-interval between two defrost cycles
P44 sets the min. time-interval between a defrost cycle and the next one.
Access:
Keypad: if C50=1, 3 or 4 Ü press for 5 seconds;
if C50=0 or 2 Ü the parameter can only be displayed.
Remote control: if C50=0, 1 or 4 Ü press “ENABLE” and and ;
if C50=2 or 3 Ü the parameter can only be displayed.
Modes: only when C00=8
Other parameters: does not depend on other parameters.
Operating range: from 1 to 240 minutes.
Default: 1 minute.
Note: if the duration of the defrost cycle (P43) is greater than or equal to P44, the defrost will go on provided that the value of the
variable remains below P40.
P45: Value of the output during defrost
P45 sets the value of the 0÷10 V analogue output during a defrost cycle.
Access:
Keypad: if C50=1, 3 or 4 Ü press for 5 seconds;
if C50=0 or 2 Ü the parameter can only be displayed.
Remote control: if C50=0, 1 or 4 Ü press “ENABLE” and and ;
if C50=2 or 3 Ü the parameter can only be displayed.
Modes: only when C00=8.
Other parameters: does not depend on other parameters.
Operating range: from 0 to 100%.
Default: P45 = 0.
8.8 Parameters concerning keypad and remote control
C50: Enabling keypad and remote control
C50 allows you to limit or prevent any modification of the parameters by non authorized personnel.
Access:
Keypad: + for 5 seconds and password 77;
Remote control: if C50=4 Ü press “ENABLE” and and
.
Other parameters: does not depend on other parameters.
Operating range: from 0 to 4
C50=0 Ü Keypad: disabled (parameters can be only displayed except C50)
Remote control: parameters P and set-point can be modified, parameters C can't be seen;
C50=1 Ü Keypad: enabled;
Remote control: parameters P and set-points can be modified; parameters C can't be seen;
C50=2 Ü Keypad: disabled (only displayed parameters, except C50);
Remote control: disabled (parameters P and set-point can only be displayed);
C50=3 Ü Keypad: enabled;
Remote control: disabled (parameters P and set-point can only be displayed);
C50=4 Ü Keypad: enabled;
Remote control: enabled;
Default: C50 = 4 Ü Keypad and remote control enabled.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Carel FCM0002000 and is the answer not in the manual?

Carel FCM0002000 Specifications

General IconGeneral
BrandCarel
ModelFCM0002000
CategoryController
LanguageEnglish

Related product manuals