3.
X
Hold down (C) for at least two seconds
until [INDICATE] starts to flash. Release
the button when the second hand moves
to [R].
When a connection is established
between the watch and phone and
location information acquisition is
successful, [INDICATE] will change to
[OK], and the second hand will move from
[R] to [C].
After two seconds the distance from your
current location to the recorded location
will appear on the display, and the second
hand will indicate the bearing to the
destination.
Distance from your current
location
Bearing to destination
After two seconds
Second hand
*2
*1
*1
When the second hand is within the range
between 55 seconds to 05 seconds
(indicating that you are within 30 degrees
of the bearing to the destination), [
] will
be displayed as a light figure on a dark
background.
*2
[G] is shown on the display when you are
within 80 meters of the destination. [G] will
disappear from the display if you move to
a distance of 161 meters or more from the
destination.
4.
X
Check the display distance and the
bearing to your destination on the display.
Note
●
Location Indicator remains enabled for
three minutes.
●
The watch connects with the phone
and acquires location information
every 10 seconds or each time (B) is
pressed, and uses the information to
refresh the distance and the bearing to
the point stored in Location Memory.
●
Location Indicator will become
disabled automatically about three
minutes after it is enabled. You can
also disable it manually by pressing
any button besides (B) or (L).
●
Pressing (B) or (L) while Location
Indicator is enabled will cause it to
remain enabled for three minutes after
the button is pressed.
●
Pressing (B) to update data causes [
TRY] to appear on the display and
remain displayed until data updating is
complete.
●
[
FAIL] will appear on the display in
the cases below.
ー
When it has been 30 seconds or
more since the last update and
location information acquisition fails
ー
When it has been 60 seconds or
more since the last update
ー
When data acquisition fails after you
press (B)
●
The display range for the distance to a
destination is 0 to 99,999 meters (0 to
327,995 feet). [
-----] will be shown
for the distance to the destination when
it is outside the display range.
●
[ERR] will appear on the display if
connection fails for some reason.
●
The message [NO-DATA] will appear
when there is no data in Location
Memory.
●
[FAILED]
n
[POSITION] will appear in
sequence if the first location
information acquisition fails.
●
[
] or [G] will flash on the display if the
watch detects abnormal magnetism
while Location Indicator is in use.
●
[ ERR] will appear on the display if a
direction sensor error occurs while
Location Indicator is in use.
Auto Altitude Calibration
Enabling auto altitude calibration with PRO
TREK Connected will cause altitude values to
be acquired by PRO TREK Connected, which
will be used to automatically correct the
watch’s altitude reading.
Important!
●
Use PRO TREK Connected to enable
or disable auto altitude calibration. It
cannot be enabled or disabled on the
watch.
Note
●
If an altitude value acquired by PRO
TREK Connected satisfies accuracy
conditions, the watch will automatically
correct is altitude reading.
●
Auto altitude calibration is performed
at the same time as auto time
adjustment.
●
Auto altitude calibration is not
performed for 12 hours after the time
setting is adjusted manually.
Configuring World Time
Settings
Specifying a World Time City with PRO TREK
Connected causes the watch’s World Time
City to change accordingly. The standard
time/summer time setting of the World Time
will be adjusted automatically without any
watch operation required by you.
Note
●
PRO TREK Connected World Time
lets you select from among
approximately 300 cities as the World
Time City.
Operation Guide 5602
13
To Next Page
Loading...
Need help?
General
