246
Appendix (Error code)
Error code (…continued)
Error
code
Message Meaning Action
E051
E053
E054
E055
E059
E060
E061
E062
E064
E066
E070
E071
E073
E075
E085
E099
E100
E101
E103
E105
E106
E110
E121
E139
E140
E146
E164
E165
E166
E176
E200
E203
E205
CHK/TBL No. is
occupied
CHK/TBL No. is
not opened
Out of CHK/TBL
No. range
In the SEP CHK
operation
Press EAT-IN or
TAKE-OUT key
Printer offline
Printer error
Printer paper
end
Print buffer
full
Print from the
beginning of the
transaction
Target print ter
minal busy/down
Target terminal
print BF full
Your receipt/ord
er may not be is
sued
Negative balance
cannot be
finalized
Data exist in
consolidation
file
Check NFP items
Operate at the
master terminal
PLU maintenance
file full. Press
<#2> to exit
PLU Code is not
exist. Input PLU
Code
PLU file full
Item exists in
the PLU FILE
Master is busy/d
own. Retry:<CA>
Remove:<ST>
Inline startup
error
Negative balance
is not allowed
Wrong menu
Arrangement file
full
Employee No. is
not Found in the
Employee File
Employee No. is
not Clocking-in
Employee No. is
Occupied
Time&Attendance
file full
Insert CF card
Insufficient
memory
File already
exist.
Attempt to made use <NEW CHECK> to open a new check
using a number that is already used for an existing check in
check tracking memory.
Attempt made to use <OLD CHECK> reopen a new check
using a number that is not used for an existing check in check
tracking memory.
Check number range over.
Normal registration is prohibited during separate check
operation.
Attempt to finalize a transaction without specifying <EAT-
IN> or <TAKEOUT>.
External (local) printer offline
External (local) printer went down.
External (local) printer paper end
External (local) printing buffer full
Attempt to print the last separated transaction on slip.
The terminal connected with the external (remote) printer is
busy or goes down.
The print buffer of the terminal connected with the external
(remote) printer becomes full.
The terminal connected with the external (remote) printer
goes down,
Attempt to finalize a transaction when balance is less than or
equal to zero.
Data exists in the consolidation file.
Disable to read/reset or consolidate the not found PLU item.
Prohibit master operation.
Scanning PLU direct maintenance/batch maintenance file
becomes full.
The PLU code you input is not existed in the PLU file.
Scanning PLU/not found PLU file full
The designated item has already existed in the scanning PLU
file.
The check tracking master terminal is busy or goes down.
Network startup error.
Attempt to register <–> or <CPN> when the balance becomes
negative.
This sheet holder is prohibited by PGM.
Arrangement file is full.
The employee number does not exist in the employee file.
The employee number has not been clocked-in yet.
The employee number has already been clocked-in.
Time and attendance file becomes full.
No CF card is set.
Insufficient memory in the CF card.
Can not write, because designated file has already been in the
CF card.
Finalize and close the check that is currently under the
number that you want to use or use a different check number.
Use the correct check number (if you want to reopen a check
that already exists in check tracking memory) or use <NEW
CHECK> to open a new check.
Enter correct number.
Terminate separate check operation.
Press <EAT-IN> or <TAKEOUT>.
Replace new paper.
Print from the beginning of the transaction
Register item(s) until the balance becomes positive amount.
Clear the data.
Perform it at master terminal.
Terminate the maintenance.
Input the correct PLU code again.
Modify the designated item.
Follow the prompt message.
Enter proper minus/coupon amount.
Set correct sheet holder.
Set the arrangement properly.
Enter the correct employee number.
Enter the correct employee number.
Enter the correct employee number,
Issue the time and attendance reset report.
Set CF card.
Use a vacant (formatted) CF card.
Check the operation and retry.
To Next Page
Loading...
