CCL 216B - Junction to Junction Forwarding; Memory Dialing; Operator Extension Setting; Password

To allot group 0 to a Junctio n= Dial #* 0000 + 50 J 0 #
To allot group 8 to a Junctio n= Dial #* 0000 + 50 J 8 #
Where, J = Junctio n Numb er (1-2)
.
. Junction to Junction Forwarding .
There are 2 types of Junction to Junction Transfer:
1. Incoming Junction Call on Ext to be transferred to another Tel Number/Cell number.
2. Making 2 Junction lines talk to each other while Ext remains out of the conversation.
Incoming Junction Call on Ext to be transferred to another Tel Number/Cell number
Any of the Extension can feed in a Telephone Number or Cell number on its extension whereby the incoming calls on its
extension would get diverted to those numbers.
While talking a tone will be heard after 2 minutes and if  is pressed then the call would get extended for another 2
minutes. Like this user can keep extending the talk time. If  is not pressed then the calls will disconnect. If user wishes to
disconnect in between then # need to be pressed.
Programming:
Dial from your own Extension #84* Tel No (where calls are to be diverted to) #
Increasing or decreasing the Talk time in such forwarded calls:
#84TT
Where, TT= 01 to 99.
In default TT = 09 x 10 = 90 Secs (80 secs talk time and 10 secs Alert Time)
To cancel the feature, dial from your own Extension #84#
Making 2 Junction lines talk to each other while Ext remains out of the conversation.
Process: During conversation with a Junction line - Hook-Flash - #6 (To park the Call) – 0 – Tel No (who is to
be connected to the previous Junction call) – Hook Flash - #  - Now all 3 party can talk to each other.
but Ext can keep Handset down. The 2 Junction lines will hear a tone after 2 minutes and if any of them
presses * then they can talk for another 2 minutes. Like this they can keep extending the talk time. If * is
not pressed then the calls will disconnect. If they wish to disconnect in between then any of them need to
dial #.
Memory Dialing .
The PBX has memo ry for 48 telepho ne numb er that can be dialed from an extensio n by dialing 2 digits codes. However,
if the ext is given only local dialing facility, then it canno t dial STD numb er of the memory.
Storing Telepho ne number in memory:
Dial #*0000 35 CC J NN#
Where CC= Memory location (01-4 8)
J = Junctio n Numb er (1-2) or Junctio n Group ‘0’ or Junctio n Gro up ‘8’
NN= Telep ho ne numb er maximum 16 digits
Note: In case mobile numb e rs are not dialing properly each time, add 0 or 00 before the numb er while adding.
Deleting memory codes-
To delete a particula r dialing code: Dial #*000 0+ 35 CC#
To delete all memo ry dialing code: Dial #*0000+ 36#
Memory Dialing Enable/Dis able-
To Enable Dial #*0000 + 37 0#
To Disable Dial #*000 0 + 37 1#
Default: Disabled
Note- If memory dialing is disabled then it will check the Junctio n dialing control for extensio n.
To dial a number from memory- Dial 7CC
. Operator Extension Setting .
In default Extensio n numb er 602 is defined as Operato r and this extensio n can be chang ed if desired by the user.
To chang e the Operato r Extensio n,
Dial #* 0000 + 15NN#
Where, NN = Last two digits of Extensio n which is to be made the Operato r.
Default: Operato r Extensio n is 602
To call operato r Dial 9
Password .
There is only one Passwo rd for the whole PBX program ming and this Passwo rd can be chang ed by the user. The default
Passwo rd is 0000.
Process to chang e the Passwo rd : #* 0000 + 09 XXXX# Here, 0000 = Default passwo rd
XXXX = New Passwo rd