CCL 216B - Junction Call Hold + Transfer; Junction Dialing Delay Time; Junction Line Ring Assignment; Direct Ring Mode (Calls land on Operator or defined extensions in Simultaneous Ring mode or Round Robin Ring mode)

Junction Call Hold + Transfer .
.
To transf er a Junctio n line to anothe r extensio n, FLASH and dial the Extensio n numb e r while talking on the junction line.
Now there can be following 4 conditions:
1. When called extensio n lifts, calling extensio n can converse and then keep the Hand set down. The Junctio n call
will then get transf erred .
2. Called extensio n lifts but doesn’t want to talk then he may keep the Handset down.
The call will come back to the transf erring extensio n.
3. The called extensio n is ringing but not lifting the Handset. Keep the Handset down.
The call will ring on the called extensio n for 25 secs and if not answered it will ring back on the transf erring
extensio n. Now if the Transf erring extensio n is busy, the Junctio n call will keep waiting for the Transf erring
extensio n to get free.
4. If the called Extensio n is engaged , the user will hear 2 tones. Now FLAS H to get back to the Junctio n line. If FLASH
is not done within 10 secs, the Junctio n line will get connected. This is the default setting in the PBX.
Alternately the user can chang e to the following mode:
On dialing an engaged extensio n user would get engaged tone. During the engaged tone user can FLASH and
get connected to the Junctio n line.
Programming : Dial #* 0000 + 831 #
To shift back to the default setting: Dial #* 0000 + 830 #
. Junction Dialing Delay Time .
This is the time after the last two digits dialed by an extensio n on Junctio n
Line. It is 7 secs in default.
The PBX assumes call maturity from after the lapse of this time.
The FLAS H function to hold an Incoming Junctio n call starts working after the lapse of this time.
To chang e this delay time, Dial #* 0000 + 03 TT # Where, TT= 01 to 99 secs. Default value = 07 (7 secs)
Junction Line Ring Assignment .
Junctio n lines incoming ring can be set in the Direct ring modes:
Direct Ring Mode (Calls land on Operato r or defined extensio ns in Simultaneo us Ring mode or Round Robin
Ring mode)
Direct Ring Mode (Simultaneous / Round Robin) Simultaneous Ring
In this mode, incoming Junctio n lines ring on one or more Extensio ns.
Incoming ring of Junctio n Lines can be program m ed separately for Day and Night modes as described
below: Dial #* 0000 + 3 J M 0 + NN
1
+ NN
2
…..+ N N
12
#
J = Junctio n Numb er (1-2)
M = 0 for Day mode/ 1 for Night Mode
NN
1
- NN
12
= The last two digits of Original extensio n numb e rs (01-32) where ring is
required . (Not the flexible numb er)
Round Robin Ring
In this mode, the incoming Junction call lands on one extension. If that extension is busy or doesn’t respond within few ring s then the
call shifts to another extension.
Programming :
Dial #* 0000 + 3 J M 1 + N
1
+ N
2
…..+ N
12
#
J = Junctio n Numb er (1-2)
M = 0 for Day mode/ 1 for Night Mode
N
1
- N
12
= The last two digits of Original extensio n numb e rs (01-32) where ring is
required . (Not the flexible numb er)
When all assigned extension s are busy
When the extensio ns assigned for the Junctio n incoming call are busy, The assigned extensio n when busy, will hear a
waiting call beep after every 5 second s. On flashing ext will get connected to incoming junction call.
Default: All the Junctio n Lines land on Extensio n numb er 601 and 602 in Simultan eo us Mode.
. Junction Line - Enable / Disable .
To Enable Junctio n Line, Dial #* 0000 + 060 J #
To Disable Junctio n Line, Dial #* 0000 + 061 J#
Where, J = Junctio n Numb er (1-2)
Note: In default Junctio n Lines are disable.
Junction Grouping .
Two set of Junctio n groups can be made. One group can be accessed say by dialing 0 and the other group of Junctio n
lines by dialing 8.