Cisco 7925G Installing Guide

Wireless LAN Settings for Cisco Unified Wireless IP Phone 7925G, 7925G-EX,
and 7926G
Before the phone can connect to the WLAN, you must configure the network profile for the phone with the
WLAN settings. You can use one of the following methods for setting up the network profiles.
WLAN Settings from Cisco Unified Wireless IP Phone Web Pages
You can access the Cisco Unified Wireless IP Phone web pages to set up the WLAN settings in the network
profile. For a new phone with the factory default settings, you must use the USB cable to connect the phone
to your PC.
Related Topics
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Web Pages
WLAN Settings from Network Profile Menu on Phone
You can use the Settings menu on the phone and access the Network Profiles menu to set up the network
configuration and the WLAN configuration.
Related Topics
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Settings
Headset Usage
Although Cisco performs some internal testing of third-party wired and Bluetooth wireless headsets for use
with the wireless phone, Cisco does not certify or support products from headset or handset vendors. Because
of the inherent environmental and hardware inconsistencies in the locations where phones are deployed, there
is not a single “best” solution that is optimal for all environments. Cisco recommends that customers test the
headsets that work best in their environment before deploying a large number of units in their network.
Use CSA or ATEX qualified Bluetooth accessories with the Cisco Unified Wireless IP Phone 7925G-EX
in hazardous environments.
Caution
Cisco recommends the use of good quality external devices, like headsets that are screened against unwanted
radio frequency (RF) and audio frequency (AF) signals. Depending on the quality of these devices and their
proximity to other devices such as cell phones and two-way radios, some audio noise may still occur.
The primary reason that a particular headset would be inappropriate for the phone is the potential for an audible
hum. This hum can be heard by either the remote party or by both the remote party and the phone user. Some
humming or buzzing sounds can be caused by a range of outside sources; for example, electric lights, being
near electric motors or large PC monitors. In some instances, the mechanics or electronics of various headsets
can cause remote parties to hear an echo of their own voice when they speak to phone users.
Related Topics
External Device Use, on page 16
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
14
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Setup
Wireless LAN Settings for Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g