Cisco 7925G Installing Guide

BAT is included in Cisco Unified Communications Manager 5.0 or later, but it is a plug-in for earlier
releases.
Note
For detailed instructions about using BAT, see the following documents:
•
For Cisco Unified Communications Manager Release 5.0 and earlier, see Bulk Administration Tool User
Guide for Cisco Unified Communications Manager.
•
For Cisco Unified Communications Manager Release 6.0 and later, see Cisco Unified Communications
Manager Bulk Administration Guide.
When using BAT to add a Cisco Unified Wireless IP Phone, use the default setting for the phone load.
The phone load name includes symbols (-, _, .) and BAT does not permit symbols in an entry.
Note
Cisco Unified Communications Manager Administration Phone Addition
Add phones individually by using Cisco Unified Communications Manager Administration. To do so, obtain
the MAC address for each phone before you begin. See Cisco Unified Communications Manager Phone
Addition Methods, on page 2 for instructions.
Perform one of the following after collecting the MAC addresses:
•
Cisco Unified Communications Manager Release 5.0 or later: Choose Device > Phone and click Add
New.
•
Cisco Unified Communications Manager Release 4.x: Choose Device > Add a New Device.
For additional instructions and conceptual information about Cisco Unified Communications Manager, see
the Cisco Unified Communications Manager Administration Guide and Cisco Unified Communications
Manager System Guide.
Device Support
Cisco Unified Communications Manager Release 4.3 and later require a device package or service release
update installed to enable device support for the Cisco Unified Wireless IP Phone. Device packages including
support for the Cisco Unified Wireless IP Phone are available at http://www.cisco.com/kobayashi/sw-center/
sw-voice.shtml.
Safety Information
Review the following warnings before installing the Cisco Unified Wireless IP Phone. To see translations of
these warnings, see the Regulatory Compliance and Safety Information for the Cisco Unified Wireless IP
Phone 7920 Series and Peripherals document that accompanied the device.
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Administration Guide
4
Cisco Unified Wireless IP Phone 7925G, 7925G-EX, and 7926G Setup
Device Support

Cisco 7925G Specifications

General

Keypad number of keys	12
Display diagonal	2 \
Display resolution	176 x 220 pixels
Call waiting	Yes
Lines quantity	6 lines
Voice codecs	G.711a, G.722, G.729a, iLBC
Security algorithms	128-bit WEP, SSL/TLS, WPA
Supported network protocols	DHCP, TFTP, DNS, SCCP, SRST
Input voltage	100 - 240 V
Dimensions (WxDxH)	52 x 20 x 127 mm
Minimum system requirements	Cisco Unified Communications Manager 4.1, 4.2, 4.3, 5.1, 6.0, 6.1, 7.0 + Cisco Unified Communications Manager Express 4.3 +
Input frequency	50/60 Hz
Storage temperature (T-T)	-30 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Product type	IP Phone
Product color	Gray
Safety	UL 60950, CSA 22.2 No.60950, EN 60950, IEC 60950, AS/NZS 60950, IEC 60529 (IP 54)
Certification	47 CFR 15 B ICES-003 B EN 55022 B AS/NZS CISPR 22 B CISPR 22 B VCCI B EN 61000-3-2 EN 61000-3-3 KN 22 EN 55024 EN 50082-1 EN 61000-6-1 EN 300386 EN 60601-1-2 KN
Compliance industry standards	IEEE 802.11a, IEEE 802.11b, IEEE 802.11g, IEEE 802.1X, IEEE 802.11e

Weight and Dimensions

Weight	138 g