Cisco ASR 1002 User Manual

Page 38 of 72
4.6.4.3 Authenticating the Certificate Authority
The TOE must authenticate the CA by acknowledging its attributes match the publicly posted
fingerprint. The TOE administrator must verify that the output of the command below matches
the fingerprint of the CA on its public site.
1. Authenticate the CA: crypto ca authenticate trustpoint-name
Device (config)#crypto ca authenticate ciscotest
Certificate has the following attributes:
Fingerprint MD5: 8DE88FE5 78FF27DF 97BA7CCA 57DC1217
Fingerprint SHA1: 271E80EC 30304CC1 624EEE32 99F43AF8 DB9D0280
% Do you accept this certificate? [yes/no]: yes
Trustpoint CA certificate accepted.
4.6.4.4 Storing Certificates to a Local Storage Location
Certificates are stored to NVRAM by default; however, some routers do not have the required
amount of NVRAM to successfully store certificates. All Cisco platforms support NVRAM and
flash local storage. Depending on the platform, an authorized administrator may have other
supported local storage options including bootflash, slot, disk, USB flash, or USB token. During
run time, an authorized administrator can specify what active local storage device will be used to
store certificates. For more detailed information see the Public Key Infrastructure Configuration
Guide Guidance document section "How to Configure PKI Storage." -
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_pki/configuration/xe-3s/sec-pki-xe-
3s-book.pdf
4.6.4.4.1. How to Specify a Local Storage Location for Certificates
The summary steps for storing certificates locally to the TOE are as follows:
1. Enter configure terminal mode:
Device # configure terminal
2. Specify the local storage location for certificates: crypto pki certificate storage
location-name
Device(config)# crypto pki certificate storage flash:/certs
3. Exit:
Device(config)# exit
4. Save the changes made:
Device# copy system:running-config nvram:startup-config
5. Display the current setting for the PKI certificate storage location:
Device# show crypto pki certificates storage
The following is sample output from the show crypto pki certificates storage command, which
shows that the certificates are stored in the certs subdirectory of disk0:
Device# show crypto pki certificates storage
Certificates will be stored in disk0:/certs/

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g