EasyManuals Logo

Cisco Catalyst 2960-X Command Reference

Cisco Catalyst 2960-X
134 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #106 background imageLoading...
Page #106 background image
spanning-tree mst pre-standard
To configure a port to transmit only prestandard bridge protocol data units (BPDUs), use the spanning-tree
mst pre-standard command in interface configuration mode. To return to the default settings, use the no
form of this command.
spanning-tree mst pre-standard
no spanning-tree mst pre-standard
Syntax Description
This command has no arguments or keywords.
Command Default
The default is to automatically detect prestandard neighbors.
Command Modes
Interface configuration
Command History
ModificationRelease
This command was introduced.Cisco IOS 15.0(2)EX
Usage Guidelines
The port can accept both prestandard and standard BPDUs. If the neighbor types are mismatched, only the
common and internal spanning tree (CIST) runs on this interface.
If a switch port is connected to a switch running prestandard Cisco IOS software, you must use the
spanning-tree mst pre-standard interface configuration command on the port. If you do not configure
the port to send only prestandard BPDUs, the Multiple STP (MSTP) performance might diminish.
Note
When the port is configured to automatically detect prestandard neighbors, the prestandard flag always appears
in the show spanning-tree mst commands.
Examples
This example shows how to configure a port to transmit only prestandard BPDUs:
Switch(config-if)# spanning-tree mst pre-standard
Related Commands
DescriptionCommand
Enables BPDU filtering on the interface.
spanning-tree bpdufilter
Enables BPDU guard on the interface.
spanning-tree bpduguard
Enables PortFast on the interface.
spanning-tree portfast (interface configuration)
Catalyst 2960-X Switch Layer 2 Command Reference, Cisco IOS Release 15.0(2)EX
100 OL-29043 -01
Layer 2 Commands
spanning-tree mst pre-standard

Table of Contents

Other manuals for Cisco Catalyst 2960-X

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 2960-X and is the answer not in the manual?

Cisco Catalyst 2960-X Specifications

General IconGeneral
Console portRJ-45
USB 2.0 ports quantity2
SFP module slots quantity4
Installed SFP modules quantity-
Gigabit Ethernet (copper) ports quantity48
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Power sourceAC
Input current5 A
AC input voltage100 - 240 V
Power consumption (typical)60.9 W
Number of power supply units1
Redundant power supply (RPS) supportYes
Operating altitude0 - 3000 m
Non-operating altitude0 - 4000 m
Storage temperature (T-T)-25 - 70 °C
Operating temperature (T-T)-5 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Switching protocolsUDP, TCP, RADIUS/TACACS+
Number of VLANs1023
Networking standardsIEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput107.1 Mpps
Jumbo frames9216
Number of queues8
MAC address table16000 entries
Number of static routes1000
DHCP featuresDHCP server
AuthenticationMAC-based authentication, Port-based authentication
Security algorithms802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules3
Switch typeManaged
Switch layerL2/L3
SafetyUL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor1U
Product colorBlack
Total Power over Ethernet (PoE) budget370 W
Power over Ethernet (PoE) ports quantity24
Power over Ethernet plus (PoE+) ports quantity12
Memory typeDRAM
Noise level39 dB
Flash memory128 MB
Internal memory512 MB
Processor frequency600 MHz
Mean time between failures (MTBF)276870 h
Weight and Dimensions IconWeight and Dimensions
Depth368 mm
Width445 mm
Height45 mm
Weight5800 g

Related product manuals