EasyManuals Logo

Cisco Catalyst 2960-X Command Reference

Cisco Catalyst 2960-X
134 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #114 background imageLoading...
Page #114 background image
spanning-tree portfast (interface configuration)
To enable PortFast mode where the interface is immediately put into the forwarding state upon linkup without
waiting for the timer to expire, use the spanning-tree portfast command in interface configuration mode.
To return to the default settings, use the no form of this command.
spanning-tree portfast [disable| trunk]
no spanning-tree portfast
Syntax Description
(Optional) Disables PortFast on the interface.disable
(Optional) Enables PortFast edge mode on the interface.trunk
Command Default
The settings that are configured by the spanning-treeportfastdefault command.
Command Modes
Interface configuration
Command History
ModificationRelease
This command was introduced.Cisco IOS 15.0(2)EX
Usage Guidelines
You can enable this feature when the switch is operating in the per-VLAN spanning-tree plus (PVST+), Rapid
PVST+, or the multiple spanning-tree (MST) mode.
This feature affects all VLANs on the interface.
Use this command only on interfaces that connect to end stations; otherwise, an accidental topology loop
could cause a data-packet loop and disrupt the switch and network operation.
To enable PortFast on trunk ports, you must use the spanning-tree portfast trunk interface configuration
command. The spanning-tree portfast command is not supported on trunk ports.
An interface with the PortFast feature enabled is moved directly to the spanning-tree forwarding state without
the standard forward-time delay.
You can use the spanning-tree portfast default global configuration command to globally enable the PortFast
feature on all nontrunking interfaces. Use the spanning-tree portfast interface configuration command to
override the global setting.
If you configure the spanning-tree portfast default global configuration command, you can disable PortFast
on an interface that is not a trunk interface by using the spanning-tree portfast disable interface configuration
command.
Catalyst 2960-X Switch Layer 2 Command Reference, Cisco IOS Release 15.0(2)EX
108 OL-29043 -01
Layer 2 Commands
spanning-tree portfast (interface configuration)

Table of Contents

Other manuals for Cisco Catalyst 2960-X

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Catalyst 2960-X and is the answer not in the manual?

Cisco Catalyst 2960-X Specifications

General IconGeneral
Console portRJ-45
USB 2.0 ports quantity2
SFP module slots quantity4
Installed SFP modules quantity-
Gigabit Ethernet (copper) ports quantity48
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Power sourceAC
Input current5 A
AC input voltage100 - 240 V
Power consumption (typical)60.9 W
Number of power supply units1
Redundant power supply (RPS) supportYes
Operating altitude0 - 3000 m
Non-operating altitude0 - 4000 m
Storage temperature (T-T)-25 - 70 °C
Operating temperature (T-T)-5 - 40 °C
Operating relative humidity (H-H)10 - 95 %
Switching protocolsUDP, TCP, RADIUS/TACACS+
Number of VLANs1023
Networking standardsIEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput107.1 Mpps
Jumbo frames9216
Number of queues8
MAC address table16000 entries
Number of static routes1000
DHCP featuresDHCP server
AuthenticationMAC-based authentication, Port-based authentication
Security algorithms802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules3
Switch typeManaged
Switch layerL2/L3
SafetyUL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor1U
Product colorBlack
Total Power over Ethernet (PoE) budget370 W
Power over Ethernet (PoE) ports quantity24
Power over Ethernet plus (PoE+) ports quantity12
Memory typeDRAM
Noise level39 dB
Flash memory128 MB
Internal memory512 MB
Processor frequency600 MHz
Mean time between failures (MTBF)276870 h
Weight and Dimensions IconWeight and Dimensions
Depth368 mm
Width445 mm
Height45 mm
Weight5800 g

Related product manuals