Cisco Catalyst 2960-X Command Reference

switchport access vlan
To configure a port as a static-access, use the switchport access vlan command in interface configuration
mode. To reset the access mode to the default VLAN mode, use the no form of this command.
switchport access vlan vlan-id
no switchport access vlan
Syntax Description
VLAN ID of the access mode VLAN. The range is 1 to 4094.
vlan-id
Command Default
The default access VLAN and trunk interface native VLAN is a default VLAN corresponding to the platform
or interface hardware.
A dynamic-access port is initially a member of no VLAN and receives its assignment based on the packet it
receives.
Command Modes
Interface configuration
Command History
ModificationRelease
This command was introduced.Cisco IOS 15.0(2)EX
Usage Guidelines
The port must be in access mode before the switchport access vlan command can take effect.
If the switchport mode is set to access vlan vlan-id, the port operates as a member of the specified VLAN.
An access port can be assigned to only one VLAN.
The no switchport access command resets the access mode VLAN to the appropriate default VLAN for the
device.
Examples
This example shows how to change a switched port interface that is operating in access mode to operate in
VLAN 2 instead of the default VLAN:
Switch(config-if)# switchport access vlan 2
Related Commands
DescriptionCommand
Configures the VLAN membership mode of a port.
switchport mode
Catalyst 2960-X Switch Layer 2 Command Reference, Cisco IOS Release 15.0(2)EX
OL-29043 -01 115
Layer 2 Commands
switchport access vlan

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g